Loepfe YarnMaster Zenit Скачать руководство пользователя страница 10

Страница: 10 / 83

ZENIT

YARN CLEARING GENERAL

Accumulations of Faults

(Cluster)

Periodic clusters (moiré)

Non-periodic clusters

in the short, long or thin fault range which repeat them-
selves several times within a short distance.

Off-standard Bobbins

(SFI / D)

Irregularities of the surface structure such as:

Hairiness

Neppiness

Irregularity

Imperfections (IPI)

Yarn Irregularities

(VCV)

Disturbing diameter variations or sporadic irregularities, for
example:

Neppiness

Irregularity (CV)

Imperfections (IPI)

Check length adjustable between 1–50 m

Foreign Matter

(F)

Foreign matter with a color that is different from the base
color of the yarn:

Bright foreign matter in the dyed yarn

Dark foreign matter in the raw-white yarn

Even the smallest contrast differences are reliably detect-
ed in colored yarns.

Synthetic Foreign Matter

(P)

Synthetic foreign matter (e.g. polypropylene)

Irrespective of the color of the yarn and the foreign
matter, for example, white and transparent polypropyl-
ene in raw-white yarn

In dyed or colored yarn

In raw-white yarn

Periodic

Non-periodic

Hairiness

Neppiness

Irregularity

Imperfections

Neppiness

Irregularity

Imperfections

Synthetic foreign matter in raw-white yarn

Содержание YarnMaster Zenit




















































































Результаты поиска

Содержание YarnMaster Zenit

Отзывы:

Похожие инструкции для YarnMaster Zenit

Бренды по названию

Популярные бренды

Loepfe YarnMaster Zenit, Инструкция по эксплуатации

Результаты поиска

Содержание YarnMaster Zenit

Отзывы:

Похожие инструкции для YarnMaster Zenit

Бренды по названию

Популярные бренды