2NP-5
1-4-28
2550
Conveying motor 1 steady-
state error
The rated speed signal
detected the stability OFF
continuously for 1 s after the
conveying motor 1 stabilizes.
Defective connec-
tor cable or poor
contact in the con-
nector.
Reinsert the connector. Also check for conti-
nuity within the connector cable. If none,
replace the cable.
Conveying motor 1 and engine PWB (YC25)
Defective drive
transmission sys-
tem.
Check if the rollers and gears rotate
smoothly. If not, grease the bushings and
gears. Check for broken gears and replace if
any.
Defective motor.
Replace the Conveying motor 1.
Defective PWB.
1. Check the engine software and upgrade
to the latest, if necessary.
2. Replace the engine PWB and check for
correct operation (see page 1-5-39).
2560
Conveying motor 1 startup
error
Conveying motor 1 is not sta-
bilized within 2 s since the
motor is activated.
Defective connec-
tor cable or poor
contact in the con-
nector.
Reinsert the connector. Also check for conti-
nuity within the connector cable. If none,
replace the cable.
Conveying motor 1 and engine PWB (YC25)
Defective drive
transmission sys-
tem.
Check if the rollers and gears rotate
smoothly. If not, grease the bushings and
gears. Check for broken gears and replace if
any.
Defective motor.
Replace the conveying motor 1.
Defective PWB.
1. Check the engine software and upgrade
to the latest, if necessary.
2. Replace the engine PWB and check for
correct operation (see page 1-5-39).
2600
PF drive motor error
(paper feeder)
When the PF drive motor is
driven, error signal is detected
continuously for 1 s.
Defective connec-
tor cable or poor
contact in the con-
nector.
Reinsert the connector. Also check for conti-
nuity within the connector cable. If none,
replace the cable.
PF drive motor and PF main PWB
Defective drive
transmission sys-
tem.
Check if the rollers and gears rotate
smoothly. If not, grease the bushes and
gears. Check for broken gears and replace if
any.
Defective motor.
Replace the PF drive motor.
Defective PWB.
Replace the PF main PWB (Refer to the ser-
vice manual for the paper feeder).
Code
Contents
Causes
Check procedures/
corrective measures
Содержание TASKalfa 2551ci
