Kongskilde GMT 3205 L P Скачать руководство пользователя страница 164 | Manualshive

Страница: 164 / 190

background image

7 - MAINTENANCE

End of season service

When the season is over, prepare the implement for the
storage immediately.

To prepare the implement for winter storage:

1. Clean the implement thoroughly. Dust and dirt absorb

moisture and moisture increases the formation of rust.

2. Store the implement in a dry place, protected against

wind and weather in the best possible way.

3. Grease all grease fittings after you clean the imple-

ment, according to the “Maintenance planning”.

4. Check the implement for damaged parts, loose screw-

joints, leakage, wear and other defects carefully before
the storage. If there is any damage, it may be forgotten
during the storage and result in problems the following
season. Note down the necessary parts you will need
before the next season and order the spare parts.

5. Dismount the Power Take-Off (PTO) shafts, grease the

profile tubes and keep them in a dry place.

6. Spray the implement with a coat of rust-preventing oil.

7. Parts polished with use and the piston rods of the hy-

draulic cylinder may get rusty. Clean and brush with
grease parts polished with use and the piston rods to
protect against wind and weather.

8. Change the oil in the hydraulic system, the cutter bar

and the gearboxes.

9. Relieve the roll pressure (on the roll conditioning mod-

els only).

10. Remove the pressure from the conditioner drive belt.

11. Park the implement with the header lift lock valves

engaged. If the cutter bar is lowered to the ground,
place wood blocks under the cutter bar to prevent di-
rect ground contact.

12. Check and adjust the tire pressure to

2.5 bar

(

36 psi

).

13. Support the implement to relieve the weight from the

tires. Tire and rubber components life will be extended
if protected from sunlight during storage.

NOTE:

Periodic checks will help to keep your implement

maintenance and repairs to a minimum and avoid costly
breakdowns during the season. Therefore, it is good prac-
tice to have the implement inspected at the end of the sea-
son.

7-58

«
...
162
163
164
165
166
...
»

Содержание GMT 3205 L P































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GMT 3205 L P

Бренд: Ecco Страницы: 4

Бренд: JD Squared Страницы: 15

Бренд: DAPAudio Страницы: 16

Бренд: 3M Страницы: 28

Бренд: Jacobsen Страницы: 6

Бренд: Latchways Страницы: 80

Бренд: Kapriol Страницы: 28

Бренд: Tascam Страницы: 27

Бренд: Jay-Lor Страницы: 72

Бренд: MacDon Страницы: 198

Бренд: M-Triangel Страницы: 6

Бренд: h/p/cosmos Страницы: 81

Бренд: Taurus Страницы: 24

Pressure Governor

Бренд: Waterous Страницы: 53

Бренд: Landi Renzo Страницы: 16

Бренд: IBM Страницы: 163

HQ Power VDL25BM

Бренд: Velleman Страницы: 3

Бренд: iGuzzini Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды