Kongskilde GMT 3205 L P Скачать руководство пользователя страница 149

Страница: 149 / 190

7 - MAINTENANCE

Replacement of spring plate

Each disc has one spring plate

(1)

that secures both

blades. Replace the spring plate

(1)

immediately if any

of the following conditions exist:

• The blade holder does not secure the blade firmly to

the disc.

• The diameter A of the blade pin is less than

15 mm

(

0.59 in

• The blade pin

(2)

is severely worn on one side.

NOTICE:

The blades and spring plates are heat treated

for wear resistance. If a blade or a disc is damaged, do
not attempt to weld the parts together. Replace only with
genuine KONGSKILDE spare parts.

NHIL17HT01032AB

Use the provided clearance gauge

(3)

to determine

if the blade pin diameter is sufficient. The clearance
gauge should not fit over the shank of the blade pin

(2)

NHIL17HT01033AB

To replace the spring plate, proceed as follows:

1. Remove the bolts

(4)

that secure the cover

(5)

on the

disc

(6)

NOTE:

The end discs do not use covers. Remove the hex

socket bolts to remove the disc.

2. Remove the cover

(5)

3. Remove the bolts

(7)

that secure the disc to the hub.

NHIL17HT01034AA

4. Remove the disc

(6)

, the spring plate

(1)

, and the

blades

(8)

5. Transfer the blades to the blade pins on the new spring

plate.

NHIL17HT01035AA

7-43

Содержание GMT 3205 L P































































































































































































Результаты поиска

Содержание GMT 3205 L P

Отзывы:

Похожие инструкции для GMT 3205 L P

Бренды по названию

Популярные бренды

Kongskilde GMT 3205 L P, Руководство оператора

Результаты поиска

Содержание GMT 3205 L P

Отзывы:

Похожие инструкции для GMT 3205 L P

Бренды по названию

Популярные бренды