Kongskilde GMT 3205 L P Скачать руководство пользователя страница 110 | Manualshive

Страница: 110 / 190

background image

7 - MAINTENANCE

Grease fittings and intervals

Regular lubrication is the best insurance against delays
and repairs. Proper lubrication will extend the life of the
implement.

Grease fittings

On new implements, the grease fitting may be covered
with paint. Remove the paint to ensure the grease fitting
can accept grease.

Wipe the dirt from all of the fittings and from the grease
gun nozzle before you grease the implement to minimize
the chance of contamination.

Pump fresh grease into the fitting to adequately lubricate
the component and force out any contamination from the
grease passage. Wipe off any excess grease.

Follow the lubrication schedule outlined in this operator’s
manual. Refer to the illustrations to identify each grease
fitting on this implement.

Not all grease fittings are readily visible. Various grease
fittings can only be accessed through the removal of
shields or guards. Always install the shields or guards
before you operate the implement.

Grease guns

Different types of grease guns provide a different amount
of grease per pump of the handle.

Two commonly used grease gun types are as follows:

(1)

Pistol grip-style grease gun

(2)

Lever-style grease gun

In general, a pistol grip-style grease gun injects half of the
amount of grease per pump as a lever-style grease gun.

For listed components to grease on this implement, the
number of pumps of grease for each grease location are
based on the use of a pistol grip-style grease gun

(1)

.

If you use a lever-style grease gun, use only half of the
indicated number of pumps of grease.

1431-2-58N

1

7-4

«
...
108
109
110
111
112
...
»

Содержание GMT 3205 L P































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для GMT 3205 L P

Бренд: Tascam Страницы: 128

Бренд: ParaBody Страницы: 6

Бренд: Garmin Страницы: 12

Бренд: Garmin Страницы: 13

Бренд: H&S Страницы: 54

Бренд: Samson Страницы: 2

Бренд: ABB Страницы: 4

Бренд: M-system Страницы: 4

mocon AQUATRAN 3/38

Бренд: Ametek Страницы: 85

VIMCO Sivoia SV-CCI-GRP

Бренд: Lutron Electronics Страницы: 2

Бренд: Warner Electric Страницы: 14

Бренд: Unika Страницы: 8

Бренд: Mindray Страницы: 295

Бренд: ZAMST Страницы: 14

Бренд: Trojan Страницы: 12

100 Series Z Master

Бренд: Toro Страницы: 28

RIDA qLine Scan

Бренд: R-Biopharm Страницы: 24

Бренд: Z-CAM Страницы: 45

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды