Komatsu PC45MR-30403 Скачать руководство пользователя страница 58 | Manualshive

Страница: 58 / 475

Komatsu PC45MR-30403 Скачать руководство пользователя страница 58

PRECAUTIONS FOR NOISE

When performing maintenance of the engine and you are exposed to noise for long periods of time, wear ear
covers or ear plugs while working.
If the noise is too loud, it may cause temporary or permanent hearing problems.

PRECAUTIONS FOR HIGH-PRESSURE GREASE WHEN ADJUSTING TRACK
TENSION

• Grease is pumped into the track tension adjustment sys-

tem under high pressure. If the specified procedure for
maintenance is not followed when making adjustment,
grease drain plug (1) may fly out and cause serious injury
or death or property damage.

• When loosening grease drain plug (1) to loosen the track

tension, never loosen it more than 1 turn. Loosen the
grease drain plug slowly.

• Never put your face, hands, feet, or any other part of your

body close to grease drain plug (1).

DO NOT DISASSEMBLE RECOIL SPRING

Never disassemble the recoil spring assembly.
The recoil spring assembly has a powerful spring that acts to
reduce the impact on the idler. If it is disassembled by mistake,
the spring may shoot out and cause serious personal injury or
death. If it is necessary to disassemble it, ask your Komatsu
distributor to perform the work.

SAFETY

PRECAUTIONS FOR MAINTENANCE

2-47

«
...
56
57
58
59
60
...
»

Содержание PC45MR-30403




























































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды