Komatsu PC45MR-30403 Скачать руководство пользователя | Manualshive

Страница: 447 / 475

background image

CONTROL PATTERNS OTHER THAN STANDARD CON-
TROL METHOD (FOR MACHINES EQUIPPED WITH OPER-
ATION PATTERN CHANGE-OVER VALVE)

k

k

WARNING

• When operating the machine, check that the display of the control pattern card is matched to the

operation of the machine to prevent personal injury by malfunction.
If it does not match, replace it immediately with the correct control pattern card.

• When checking the movement of the machine, operate slowly while paying attention to the safety

around the machine.

• Stop the engine, and check that the lock lever is in LOCK position, and change the control pattern

of the machine.

NOTICE
The control pattern cards are replaceable.
If the control pattern is changed, replace the control pattern card with the one for the new control pat-
tern.

The control pattern card is located at the position shown in the figure.

Machine with canopy specification

The control pattern card is located on the right side of the oper-
ator's seat.

Machine with cab specification

The control pattern card is located on the right side of the oper-
ator's seat.

The preferable control pattern can be selected for the work equipment control lever.

CONTROL PATTERNS OTHER THAN STANDARD CONTROL METH-
OD (FOR MACHINES EQUIPPED WITH OPERATION PATTERN
CHANGE-OVER VALVE)

ATTACHMENTS AND OPTIONS

6-30

«
...
445
446
447
448
449
...
»

Содержание PC45MR-30403




























































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PC45MR-30403

Бренд: jcb Страницы: 6

Бренд: Savaria Страницы: 48

Бренд: Takeuchi Страницы: 20

Бренд: Kubota Страницы: 2

Бренд: RHINO Страницы: 42

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды