Komatsu PC45MR-30403 Скачать руководство пользователя | Manualshive

Страница: 52 / 475

background image

PRECAUTIONS FOR OPENING AND CLOSING FLOOR

• Do not open the floor on the slope ground or in windy

weather, otherwise it may lead to serious personal injury or
death.

• Do not open the floor when the engine is running, the door

(if the machine is equipped with the cab) is open, or the
lock lever is in Free position, otherwise it may lead to seri-
ous personal injury or death.

• Immediately after the engine is stopped, its parts and oil

are still very hot and may cause burn injury. Check that the
temperature inside of engine compartment has been drop-
ped before performing the opening or closing of floor.

• Do not get on the operator's seat when floor is opened,

otherwise it may lead to serious personal injury or death by
fall.

TWO WORKERS FOR MAINTENANCE WHEN ENGINE IS RUNNING

To prevent an accident, do not perform the maintenance with the engine running. When it is necessary to per-
form the maintenance with the engine running, always observe the following.

• One worker must always sit on the operator's seat and be ready to stop the engine at any time. All workers

must maintain contact with the other workers.

• Rotating parts such as the fan, fan belt are dangerous that

they may easily catch a body part or an object someone
wears. Be careful not to come close to the rotating part.

• Never drop or insert tools or other objects into the fan, fan

belt, or other rotating parts. They may contact the rotating
parts and break, and be scattered. It is dangerous.

• If the automatic active regeneration of KDPF starts during

the maintenance work, the temperature around KDPF be-
comes high.

• Release the remaining pressure in the hydraulic system,

and place the lock lever (1) to LOCK position (L).

• Do not touch the control levers or pedals. When it is nec-

essary to operate the control levers or pedals, always give
a signal to your fellow workers to evacuate them to a safe
place.

,&

SAFETY

PRECAUTIONS FOR MAINTENANCE

2-41

«
...
50
51
52
53
54
...
»

Содержание PC45MR-30403




























































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PC45MR-30403

Бренд: Komatsu Страницы: 9

Бренд: Komatsu Страницы: 31

Бренд: jcb Страницы: 2

Бренд: Wacker Neuson Страницы: 188

Бренд: Komatsu Страницы: 4

Бренд: Komatsu Страницы: 6

Бренд: Komatsu Страницы: 528

Бренд: Komatsu Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды