Komatsu PC45MR-30403 Скачать руководство пользователя | Manualshive

Страница: 249 / 475

background image

PRECAUTIONS FOR OPERATION

PRECAUTIONS FOR TRAVELING

Traveling  over  boulders,  tree  stumps,  or  other  obstacles  will
cause a big shock to the chassis (and in particular to the under-
carriage), and this will cause damage to the machine. For this
reason,  always  remove  any  obstacles  or  drive  the  machine
around  them,  or  take  other  steps  to  avoid  traveling  over  such
obstacles as far as possible.
If  there  is  no  way  to  avoid  traveling  over  an  obstacle,  reduce
the travel speed, keep the work equipment close to the ground,
and  try  to  drive  the  machine  so  that  the  center  of  the  track
passes over the obstacle.

PRECAUTIONS FOR HIGH SPEED TRAVEL

On uneven roadbeds such as rock beds or uneven roads with large rocks, drive the machine with travel mode at
Lo.
When driving the machine with travel mode at Hi, set the idler
in the forward direction.

PRECAUTIONS FOR FOLDING WORK EQUIPMENT

When folding in the work equipment to the travel or transporta-
tion posture, be careful not to let the bucket hit the blade.

PRECAUTIONS FOR HITTING BLADE AGAINST OBJECTS DURING OPERATING
BLADE

Be careful not to hit the blade against rocks or boulders. This
will cause premature damage to the blade or cylinders.

MACHINE OPERATIONS AND CONTROLS

OPERATION

3-188

«
...
247
248
249
250
251
...
»

Содержание PC45MR-30403




























































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PC45MR-30403

Бренд: SMORACY Страницы: 29

Бренд: SANY Страницы: 208

Бренд: RAM Страницы: 52

Бренд: jcb Страницы: 4

Бренд: OLEO Страницы: 12

Бренд: Terex Страницы: 6

2BB-EVO FP Series

Бренд: Mobility Страницы: 60

PC850-8 BACKHOE

Бренд: Komatsu Страницы: 8

Бренд: Komatsu Страницы: 8

PC750-7 BACKHOE

Бренд: Komatsu Страницы: 41

Бренд: Komatsu Страницы: 41

Бренд: Komatsu Страницы: 51

Бренд: Komatsu Страницы: 203

Бренд: Komatsu Страницы: 412

Бренд: Komatsu Страницы: 442

Бренд: Komatsu Страницы: 446

Бренд: Komatsu Страницы: 462

Бренд: Komatsu Страницы: 758

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды