Komatsu PC45MR-30403 Скачать руководство пользователя

Страница: 194 / 475

METHOD FOR CHECKING BEFORE STARTING

Always check the items in this section before starting the engine each day.

METHOD FOR DRAINING WATER AND SEDIMENT FROM FUEL TANK

NOTICE
Do not use trichloroethylene to clean the inside of tank.

Items to be prepared
Container to catch the fuel
1.

Set the machine in the posture shown in the figure.
1) Start the engine.

2) Set the lock lever to FREE position (F).

Be sure to operate the lock lever by the operating por-
tion on the top.

3) Operate the work equipment control lever slowly to

right and left to swing the upper structure so that the
drain valve comes between the tracks.

4) Operate the work equipment control levers, and lower

the work equipment to the ground.

5) Set the lock lever to LOCK position (L).

Be sure to operate the lock lever by the operating por-
tion on the top.

6) Stop the engine.

Pull the engine rear cover (1) backward to open it.
Open the engine rear cover (1) fully and it is secured by
rod (2).

OPERATION

MACHINE OPERATIONS AND CONTROLS

3-133

Содержание PC45MR-30403



























































































































































































































































































































































































































































































Результаты поиска

Содержание PC45MR-30403

Отзывы:

Похожие инструкции для PC45MR-30403

Бренды по названию

Популярные бренды

Komatsu PC45MR-30403, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание PC45MR-30403

Отзывы:

Похожие инструкции для PC45MR-30403

Бренды по названию

Популярные бренды