Komatsu PC45MR-30403 Скачать руководство пользователя | Manualshive

Страница: 142 / 475

background image

TRAVEL SPEED SELECTOR SWITCH

k

k

WARNING

• When loading to or unloading onto/from a trailer, always drive the machine at low speed (set it to

Lo), and never operate the travel speed selector switch during travel.

• If the travel speed is switched between high-speed and low-speed while the machine is traveling,

the machine may deviate to one side, even when traveling in a straight line.
Stop the machine before switching the travel mode.

Perform the setting of speed mode after starting the engine.
Travel speed selector switch is used to switch the travel mode.

Lo display

Low-speed travel

Hi display

High-speed travel

The  travel  speed  is  automatically  set  to  low-speed  travel  (Lo)
when the starting switch key is turned to ON position.
Each  time  the  travel  speed  selector  switch  is  pushed,  travel
mode changes repeatedly as Lo → Hi → Lo.
Check  the  travel  mode  setting  at  travel  speed  display  on  the
machine monitor.
While traveling in high-speed travel (Hi), if the traction force is
needed in soft ground or on a slope, travel speed automatically
changes  to  low-speed  travel  (Lo),  although  high-speed  travel
(Hi) is lit in travel speed display.

OPERATION

EXPLANATION OF COMPONENTS

3-81

«
...
140
141
142
143
144
...
»

Содержание PC45MR-30403




























































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PC45MR-30403

Бренд: Yanmar Страницы: 310

Бренд: Takeuchi Страницы: 20

Бренд: Camon Страницы: 20

Бренд: Hyundai Страницы: 41

Бренд: jcb Страницы: 31

Бренд: Yuchai Страницы: 145

Бренд: Volvo Страницы: 238

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды