Komatsu PC45MR-30403 Скачать руководство пользователя | Manualshive

Страница: 48 / 475

background image

TOWING AND BEING TOWED

PRECAUTIONS FOR TOWING AND BEING TOWED

Always use the correct towing equipment and towing method. Any mistake in the selection of the wire rope or
drawbar or the method of towing a failed machine and being towed may lead to serious personal injury or death.

• Always confirm that the wire rope or drawbar used for towing has ample strength for the weight of the ma-

chine being towed.

• Never use the wire rope which has breaks in strands (A),

reduced diameter (B), or kinks (C). There is a danger that
the rope may break during the towing operation.

• Always wear leather gloves when handling the wire rope.
• Never tow a machine on a slope.
• During the towing operation, never stand between the tow-

ing machine and the machine being towed.

SAFETY

PRECAUTIONS FOR OPERATION

2-37

«
...
46
47
48
49
50
...
»

Содержание PC45MR-30403




























































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PC45MR-30403

Бренд: jcb Страницы: 6

Бренд: SANY Страницы: 445

Бренд: Yuchai Страницы: 157

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды