manualshive.com logo in svg

Komatsu PC45MR-30403, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
Komatsu PC45MR-30403 Скачать руководство пользователя страница 383

METHOD FOR REPLACING FUEL MAIN FILTER CARTRIDGE

k

k

 WARNING

• Immediately after the engine is stopped, the parts are still very hot. Do not replace the fuel filter car-

tridge immediately.
Wait for all of parts to cool down before starting the work.

• High pressure is generated inside the engine fuel piping system when the engine is running.

When replacing the fuel filter cartridge, wait for at least 30 seconds after stopping the engine to let
the internal pressure go down before replacing the filter.

• Do not bring any open flame close.

 

NOTICE

• Komatsu genuine fuel filter cartridges use a special filter that has highly efficient filtering ability.

When replacing the parts, Komatsu recommends using Komatsu genuine parts.

• The  common  rail  fuel  injection  system  used  on  this  machine  consists  of  more  precise  parts  than

those in the conventional injection pump and nozzles.
If any cartridge other than a Komatsu genuine filter cartridge is used, dust or dirt may get in and
cause problems with the injection system.
Never use a substitute.

• When  performing  inspection  and  maintenance  of  the  fuel  system,  be  careful  not  to  let  any  dirt  or

dust get in, more than ever before.
If dust sticks to the fuel system, wash it off thoroughly with fuel.

Items to be prepared

• Filter wrench
• Container to catch the fuel
• Cloth

1.

Pull the engine rear cover (1) backward to open it.
Open  the  engine  rear  cover  (1)  fully  and  it  is  secured  by
rod (2).

2.

Pull the cooling cover (3) backward to open it.

MAINTENANCE PROCEDURE

MAINTENANCE

4-74

Содержание PC45MR-30403




























































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды