Komatsu PC45MR-30403 Скачать руководство пользователя страница 151 | Manualshive

Страница: 151 / 475

Komatsu PC45MR-30403 Скачать руководство пользователя страница 151

BLADE CONTROL LEVER

NOTICE
If you continue the digging operation with blade for 1 hour or more, be careful about increase of the en-
gine coolant temperature.

The blade control lever is used to operate the blade.

(a) Blade LOWER

The blade control lever is pushed forward.

(b) Blade RAISE

The blade control lever is pulled back.

(N) NEUTRAL

Blade is held at current position.

SWING LOCK COVER

k

k

WARNING

When you do not perform the boom swing operation, lock the swing with the swing lock cover.
If it is not locked and the control pedal is touched by mistake, this may cause a serious injury or death.

The swing lock cover is used to lock the boom swing control
pedal.
When the boom swing control pedal is covered with the swing
lock cover, the boom swing control pedal is locked.

(F): FREE position

You can swing the boom to the right and left by operating the
boom swing control pedal.

(L): LOCK position

You cannot operate the boom swing control pedal.

BOOM SWING CONTROL PEDAL

Boom swing control pedal is used to swing the boom.

(a) Swing RIGHT

Depress right of the boom swing control pedal.

(b) Swing LEFT

Depress left of the boom swing control pedal.

(N) NEUTRAL

Boom is held at current position.

EXPLANATION OF COMPONENTS

OPERATION

3-90

«
...
149
150
151
152
153
...
»

Содержание PC45MR-30403




























































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды