Komatsu PC45MR-30403 Скачать руководство пользователя страница 235 | Manualshive

Страница: 235 / 475

Komatsu PC45MR-30403 Скачать руководство пользователя страница 235

• When the sprocket position (A) is front of the machine,

start the machine either by pushing the travel levers
(5) forward slowly or by depressing the front parts of
the travel pedals (6) slowly.

5.

Push the travel speed selector switch (7) to set the travel
speed.
Each time the travel speed selector switch (7) is pressed,
travel mode changes repeatedly as Lo → Hi → Lo.

Check the travel mode setting at travel speed display on
machine monitor (8).

REMARK

When  the  engine  is  started,  the  speed  mode  is  automati-
cally set to low-speed travel (Lo).
While  traveling  in  high-speed  travel  (Hi),  if  the  traction
force is needed in soft ground or on a slope, travel speed
automatically  changes  to  low-speed  travel  (Lo),  although
high-speed travel (Hi) is lit in travel speed display.

6.

When traveling, check that the travel alarm sounds nor-
mally.
If the alarm does not sound, ask your Komatsu distributor for repair.

MACHINE OPERATIONS AND CONTROLS

OPERATION

3-174

«
...
233
234
235
236
237
...
»

Содержание PC45MR-30403




























































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды