Komatsu PC45MR-30403 Скачать руководство пользователя | Manualshive

Страница: 374 / 475

background image

METHOD FOR LUBRICATING WORK EQUIPMENT

NOTICE

• If any unusual noise is generated from any greasing point, perform the greasing regardless of the

greasing interval.

• Perform greasing every 10 hours for the first 100 hours operation on a new machine.
• After the machine is subjected to digging work in the water, be sure to grease the wet pins.

Items to be prepared
Grease pump
1.

Set the machine in the greasing posture shown in the fig-
ure.
1) Start the engine and run it at low idle.

2) Set the lock lever to FREE position (F).

Be sure to operate the lock lever by the operating por-
tion on the top.

3) Push the blade control lever forward to lower the

blade to the ground.

4) Operate the work equipment control levers to extend

bucket cylinder and arm cylinder to their stroke end,
and then lower the boom gently.
Lower the bucket link to the ground.

5) Set the lock lever securely to LOCK position (L).

Be sure to operate the lock lever by the operating por-
tion on the top.

6) Stop the engine, and remove the starting switch key.

2.

Pump in the grease through the grease fittings shown by arrows by using a grease pump.
(1) Bucket and link connection pin (1 place)
(2) Arm and bucket connection pin (1 place)
(3) Arm and link connection pin (1 place)
(4) Bucket cylinder rod end (1 place)
(5) Link connection pin (1 place)

MAINTENANCE

MAINTENANCE PROCEDURE

4-65

«
...
372
373
374
375
376
...
»

Содержание PC45MR-30403




























































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PC45MR-30403

Бренд: jcb Страницы: 31

Бренд: Komatsu Страницы: 8

Бренд: Komatsu Страницы: 31

Бренд: Komatsu Страницы: 41

Бренд: Komatsu Страницы: 61

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды