Kohler CH980 Скачать руководство пользователя страница 97

Страница: 97 / 124

10.2

Section 10
Reassembly

2. Apply a light coat of clean engine oil to the

outside diameter of the oil seal.

3. Install the oil seal into the crankcase using a seal

driver. Make sure the oil seal is installed straight
and true in the bore and that the tool bottoms
against the crankcase. See Figures 10-2 and 10-3.

Figure 10-4. Lifter Feed Chamber Assembly
Details.

Install Flywheel End Main Bearing

If the flywheel end main bearing was removed in
servicing, install a new bearing using an arbor press
and driver.

1. Make sure the crankcase bore for the main

bearing is clean, dry and free of nicks or burrs.

2. Press the flywheel side main bearing in place

with the notch oriented in the 12 o’clock position
using an arbor press and driver. See Figure 10-5.
Make sure the bearing is fully seated against the
flange and the oil feed hole is open in the
crankcase. See Figure 10-6.

3. Apply a light coat of clean engine oil to the inner

surface of the main bearing.

Figure 10-2. Installing Oil Seal with Driver.

Figure 10-3. Installed Flywheel End Oil Seal.

Install Lifter Feed Chamber Gaskets and
Cover

1. Install the lifter feed chamber gasket, followed by

the lifter feed cover over the lifter feed chamber. If
used, position the breather baffle on top of the
parts with the winged offset down.

2. Install the three screws. Make sure all the parts

are properly aligned. Torque the screws to

6.2

N·m (55 in. lb.)

into new holes, or

4.0 N·m

(35 in. lb.)

, into used holes. See Figure 10-4.

Figure 10-5. Installing Main Bearing.

Mounting
Screws

Baffle (Used on Some
Models Only)

Cover

Gasket

Lifter
Feed
Chamber

Содержание CH980





























































































































Результаты поиска

Содержание CH980

Отзывы:

Похожие инструкции для CH980

Бренды по названию

Популярные бренды

Kohler CH980, Руководство по обслуживанию

Результаты поиска

Содержание CH980

Отзывы:

Похожие инструкции для CH980

Бренды по названию

Популярные бренды