Kohler CH980 Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 124

background image

7.9

Section 7

Electrical System and Components

7

*

NOTE

: A flashing LOW light can also occur as a

result of an inadequate ground lead
connection. Make certain the connection
location is clean and the clamp is secure.

15 Amp Rectifier-Regulators

1. Connect the tester ground lead (with spring

clamp) to the body of the rectifier-regulator
being tested.

2. Connect the tester red lead to the B+ terminal of

the rectifier-regulator and the two black tester
leads to the two AC terminals. See Figure 7-14.

5. Plug the tester into the proper AC outlet/power

for tester being used. Turn on the power switch.
The POWER light should be illuminated and one
of the four status lights may be on as well. See
Figure 7-12. This

does not

represent the

condition of the part.

Figure 7-12. Powered Tester.

6. Press the TEST button until a click is heard and

then release. See Figure 7-13. Momentarily one of
the four lights will illuminate indicating the

partial condition

of the part.

Figure 7-14. Tester Connected to 15 Amp Rectifier-
Regulator.

3. Plug the tester into the proper AC outlet/power

for tester being used. Turn on the power switch.
See Figure 7-12. The POWER light should be
illuminated and one of the four status lights may
be on as well. This

does not

represent the

condition of the part.

4. Press the TEST button until a click is heard and

then release. See Figure 7-13. Momentarily one of
the four status lights will illuminate, indicating
the condition of the part.

a. If the OK (green) light comes on and stays

steady, the part is good and may be used.

b. If any other light is displayed,* the rectifier-

regulator is faulty and should not be used.

*

NOTE

: A flashing LOW light can also occur as a

result of an inadequate ground lead
connection. Make certain connection
location is clean and clamp is secure.

Figure 7-13. Pressing Test Button.

a. If the OK (green) light comes on, disconnect

the tester black lead attached to one AC
terminal and reconnect it to the other AC
terminal. Repeat the test. If the OK (green)
light comes on again, the part is good and
may be used.

b. If any other light is displayed* in either of the

tests, the rectifier-regulator is faulty and
should not be used.

«
...
53
54
55
56
57
...
»

Содержание CH980





























































































































Отзывы:

Нет отзывов

Похожие инструкции для CH980

Бренд: Kohler Страницы: 12

Бренд: Tanaka Страницы: 10

Бренд: Vanguard Страницы: 124

Бренд: Zenoah Страницы: 4

4.2-litre V8 FSI

Бренд: Audi Страницы: 48

Бренд: FUTABA Страницы: 3

Бренд: Volvo Penta Страницы: 164

CYQD 32 Series CYQD32

Бренд: Dongfeng Chaoyang Diesel engine Co Страницы: 60

Бренд: Robin America Страницы: 24

Бренд: Honda Страницы: 60

Бренд: Honda Страницы: 120

Бренд: Motus Страницы: 32

Бренд: Marine Power Страницы: 56

Бренд: Iveco Страницы: 160

Бренд: Desert Aircraft Страницы: 8

Бренд: Habasit Страницы: 28

Бренд: YANGDONG Страницы: 50

Diesel Engine S12A2-Y2PTAW-2

Бренд: Mitsubishi Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды