Kohler CH980 Скачать руководство пользователя страница 105

Страница: 105 / 124

10.10

Section 10
Reassembly

Check Crankshaft End Play

1. Set the engine on the base, and use a dial

indicator to check the crankshaft end play
against the specification listed in Section 1.

Install Breather Assembly

1. Make sure the sealing surfaces of the crankcase

and breather cover are clean and free of any
nicks or burrs.

Do not

scrape the surfaces, as this

could result in leakage. Install the four breather
mounting studs into the crankcase if removed
during disassembly.

2. Install the breather chamber gasket as shown.

See Figure 10-38. Assemble and install breather
assembly components as illustrated in Figure
10-39. Make sure the filter does not extend above
top surface and all parts are properly aligned.

Figure 10-37. Checking Crankshaft Endplay.

Figure 10-39. Breather Assembly Details.

Figure 10-38. Breather Chamber and Gasket.

Breather Hose

Flange Nuts (4)

Breather

Gasket

Screw

Baffle

Filter

Adapter

Gasket

Studs (4)

Filter Must
Not Extend
Above
Casting

Filter

Studs (4)

Used on Serial No. 37070xxxxx and Below

Used on Serial No. 37071xxxxx and Higher

Breather Hose

Flange Nuts (4)

Breather

Gasket

Adapter

Содержание CH980





























































































































Результаты поиска

Содержание CH980

Отзывы:

Похожие инструкции для CH980

Бренды по названию

Популярные бренды

Kohler CH980, Руководство по обслуживанию

Результаты поиска

Содержание CH980

Отзывы:

Похожие инструкции для CH980

Бренды по названию

Популярные бренды