Kohler CH980 Скачать руководство пользователя страница 82

Страница: 82 / 124

8.15

Section 8

Disassembly

Remove Governor Yoke, Cross Shaft, and
Seal

1. Remove the two mounting screws securing the

yoke to the governor cross shaft. See Figure
8-61.

Figure 8-61. Removing Cross Shaft/Yoke Screws.

2. Pull the governor cross shaft out of the crankcase

and remove the seal.

Remove Lifter Feed Chamber Cover and
Gaskets

1. Remove the three screws securing the lifter feed

chamber baffle (some models only), cover, and
gaskets. Carefully separate the parts from the
crankcase. See Figure 8-62.

Remove Flywheel and PTO End Oil Seals

1. Remove the oil seals from the crankcase and

closure plate using a seal puller. See Figure 8-63.

Figure 8-63. Removing Oil Seals.

Removal of Main Bearings

NOTE

: Flywheel and PTO side main bearings

should only be removed if replacement is
required due to wear. If removal is
performed, use a press and support the
casting surface around the bearing flange.

Do not

press against or support by the

gasket/outer perimeter surface. See Figure
8-64.

Figure 8-62. Removing Lifter Feed Chamber Cover
Components.

Baffle (Some
Models Only)

Gasket

Cover

Screws

Support
This Surface

Figure 8-64. Support Surface Details.

Содержание CH980





























































































































Результаты поиска

Содержание CH980

Отзывы:

Похожие инструкции для CH980

Бренды по названию

Популярные бренды

Kohler CH980, Руководство по обслуживанию

Результаты поиска

Содержание CH980

Отзывы:

Похожие инструкции для CH980

Бренды по названию

Популярные бренды