Kohler CH980 Скачать руководство пользователя страница 60

Страница: 60 / 124

7.14

Section 7
Electrical System and Components

8. Take out the drive lever and pull the armature

out of the drive end cap. See Figure 7-24.

9. Remove the thrust washer from the armature

shaft. See Figure 7-24.

11. Remove the retainer from the armature shaft.

Save the stop collar.

NOTE:

Do not reuse the old retainer.

Figure 7-24. Armature and Lever Removed.

10. Push the stop collar down to expose the retaining

ring. See Figure 7-25.

Figure 7-25. Retaining Ring Detail.

Figure 7-26. Removing Retaining Ring.

12. Remove the drive pinion assembly from the

armature.

13. Clean the parts as required.

NOTE

Do not

soak the armature or use solvent

when cleaning. Wipe clean using a soft
cloth, or use compressed air.

Figure 7-27. Delco-Remy Starter.

Screw

Plunger

Spring

Lever

Plate

Plug

Solenoid

Frame & Field

Brush Holder

Nut

Commutator
End Plate

Screw

Bolt

Drive
End Cap

Collar

Retaining Ring

Stop

Drive

Armature

Washer

Tube

Содержание CH980





























































































































Результаты поиска

Содержание CH980

Отзывы:

Похожие инструкции для CH980

Бренды по названию

Популярные бренды

Kohler CH980, Руководство по обслуживанию

Результаты поиска

Содержание CH980

Отзывы:

Похожие инструкции для CH980

Бренды по названию

Популярные бренды