Kohler CH980 Скачать руководство пользователя страница 115 | Manualshive

Страница: 115 / 124

background image

10.20

Section 10
Reassembly

Figure 10-80. Torquing Flywheel Fastener.

Install Ignition Modules

1. Rotate the flywheel to position the magnet away

from the ignition module bosses.

2. Connect the ground lead to the single kill tab and

install the modules onto the crankcase bosses so
the tab is away from you (in). The spark plug
lead should be towards you (out). Mount the
wiring harness clamp with the loop

up

, on the

starter (No. 1) side inner module screw and route
harness through it. Attach the rectifier-regulator
ground lead to the outer screw. See Figure 10-81.

3. Slide the modules up as far away from the

flywheel as possible and snug the screws to hold
them in that position.

Figure 10-82. Setting Ignition Module Air Gap.

6. Torque the screws to

6.2 N·m (55 in. lb.)

into new

holes, or

4.0 N·m (35 in. lb.)

into used holes.

7. Repeat steps 4 through 6 for the other ignition

module.

8. Rotate the flywheel back and forth, checking for

clearance between the magnet and ignition
modules. Make sure the magnet does not strike
the modules. Check the gap with a feeler gauge
and readjust if necessary. Final Air Gap:

0.280/0.330 mm (0.011/0.013 in.)

.

9. Make sure the leads are under the molded clip on

the starter side. See Figure 10-83.

Figure 10-81. Ignition Module Mounting Details.

4. Rotate the flywheel to position the magnet

directly under one ignition module.

5. Insert a

0.30 mm (0.012 in.)

flat feeler gauge

between the magnet and the ignition module. See
Figure 10-82. Loosen the screws enough to allow
the magnet to pull the module down against the
feeler gauge.

Figure 10-83. Lead Routing Details.

Install Outer Cylinder Baffles

1. Install the outer cylinder baffles. Make sure the

spark plug lead is routed through the
corresponding opening in each baffle. Start each
of the screws. Torque the M6 shoulder screws
going through the backing shroud assembly into
the extruded holes in the baffles to

4.0 N·m

(35 in. lb.)

for first time installations, or

2.0 N·m (17.7 in. lb.)

for all reinstallations.

Feeler Gauge

Molded
Clip

Clamp

Kill Lead

«
...
113
114
115
116
117
...
»

Содержание CH980





























































































































Отзывы:

Нет отзывов

Похожие инструкции для CH980

3T-MOTORS 3T45-20

Бренд: 3T-Components Страницы: 24

Бренд: Admiral Страницы: 9

Бренд: hager Страницы: 4

Бренд: Westerbeke Страницы: 140

Бренд: Quectel Страницы: 165

ROLLOPOWER PLUS Series

Бренд: Schellenberg Страницы: 120

Бренд: Central Machinery Страницы: 30

Бренд: STG-BEIKIRCH Страницы: 9

Enduro RR 250 2016

Бренд: Beta Страницы: 110

Enduro RR 350 2013

Бренд: Beta Страницы: 134

Бренд: YS Страницы: 2

Бренд: NANOTEC Страницы: 295

Бренд: Honda Страницы: 7

Бренд: O.S. engine Страницы: 21

max-12TZ series

Бренд: O.S. engine Страницы: 41

Бренд: Barrus Страницы: 51

Бренд: Honda Страницы: 57

CNC Meldas HC Series

Бренд: Mitsubishi Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды