Kohler CH980 Скачать руководство пользователя страница 69

Страница: 69 / 124

8.2

Section 8
Disassembly

Figure 8-3. Removing Dipstick from Tube.

Figure 8-6. Removing Blower Housing.

Shut Off Fuel Supply

Drain Oil from Crankcase and Remove Oil
Filter

1. Clean the oil filter and housing area. Remove and

discard the oil filter. See Figure 8-2.

Figure 8-2. Removing Oil Filter.

2. Remove the dipstick and one of the oil drain

plugs.

Figure 8-4. Oil Drain Plug Location.

3. Allow ample time for the oil to drain from the

crankcase.

Remove Muffler

1. Remove the exhaust system and attaching

hardware from the engine.

Remove Cylinder Shrouds and Blower
Housing

1. Remove the top mounting screw and loosen the

two shoulder screws on each side. Lift off the
two cylinder shrouds. See Figure 8-5.

Figure 8-5. Removing Cylinder Shrouds.

2. Remove the four mounting screws and separate

the blower housing from the lower half. See
Figure 8-6.

Cylinder
Shroud

Drain Plug
(Starter Side
Shown)

Содержание CH980





























































































































Результаты поиска

Содержание CH980

Отзывы:

Похожие инструкции для CH980

Бренды по названию

Популярные бренды

Kohler CH980, Руководство по обслуживанию

Результаты поиска

Содержание CH980

Отзывы:

Похожие инструкции для CH980

Бренды по названию

Популярные бренды