Kohler CH980 Скачать руководство пользователя страница 112

Страница: 112 / 124

10.17

Section 10

Reassembly

Figure 10-67. Installing Nipple.

2. Install the oil filter housing assembly to the

adapter and secure with the M8 hex head
screw. Make sure the housing is flat on the
crankcase and all O-Rings remain in position.
Torque the screw to

24.4 N·m (216 in. lb.)

Figure 10-68. Torquing Nipple.

Installation

1. Make sure all sealing surfaces are clean and all

three dowel pins are in position. Install or check
that new O-Rings are around all three dowel
pins of the oil filter adapter. See Figure 10-69.

Figure 10-69. O-Rings Installed on Adapter for Oil
Filter Housing.

Figure 10-70. Installing Oil Filter Housing.

3. The oil filter may be installed now or upon

completion of engine assembly, as described in
Section 6.

Install Backing Shroud Assembly

1. To aid assembly, install the lower oil cooler hose

onto the oil filter housing prior to installation of
the backing shroud assembly, and secure with a
clamp. See Figure 10-71.

Figure 10-71. Lower Oil Cooler Hose Details.

NOTE

: New hose clamps are recommended for

reassembly, or if clamps have been
loosened (expanded) several times to
avoid leakage.

Nipple

O-Rings

Oil Filter Housing

Mounting
Screw

Содержание CH980





























































































































Результаты поиска

Содержание CH980

Отзывы:

Похожие инструкции для CH980

Бренды по названию

Популярные бренды

Kohler CH980, Руководство по обслуживанию

Результаты поиска

Содержание CH980

Отзывы:

Похожие инструкции для CH980

Бренды по названию

Популярные бренды