Kohler CH980 Скачать руководство пользователя страница 77 | Manualshive

Страница: 77 / 124

background image

8.10

Section 8
Disassembly

Figure 8-38. Removing Valve Covers.

Remove Cylinder Heads and Hydraulic
Lifters

1. Remove the pipe plug from the cylinder head to

access the screw in the upper center location. See
Figure 8-39.

Figure 8-41. Removing Cylinder Head Assembly.

6. Remove the lifters from the lifter bores. Use a

Hydraulic Lifter Tool. Do not use a magnet to
remove lifters. Mark the lifters by location, as
either intake or exhaust and cylinder 1 or 2.
Hydraulic lifters should always be reinstalled in
the same position. See Figures 8-42 and 8-43.

NOTE

: The exhaust lifters are located on the

output shaft side of the engine while the
intake lifters are located on the fan side
of the engine. The cylinder head number
is embossed on the outside of each
cylinder head. See Figure 8-43.

Electric Fuel Pump

1. Removal will be determined based on mounted

location and application. Disconnect the lead
connections, fuel line connections, and mounting
hardware as required. Properly contain any
remaining fuel.

Valve Covers

1. Remove the screw and grommet securing each

valve cover.

2. Remove the valve cover and gasket from each

cylinder head. Note the locations of individual
valve covers if they are different. See Figure 8-38.

Figure 8-39. Removing Pipe Plug.

2. Remove the five hex flange screws securing each

cylinder head. Note the locations of washers and
spacer. See Figure 8-40.

Figure 8-40. Removing Cylinder Head Fasteners.

3. Mark the position of the push rods as either

intake or exhaust and cylinder 1 or 2. Push rods
should always be reinstalled in the same
positions.

4. Carefully remove the push rods, cylinder head

and head gasket. See Figure 8-41.

5. Repeat the procedure for the other cylinder head.

Pipe Plug

Washers

Spacer

«
...
75
76
77
78
79
...
»

Содержание CH980





























































































































Отзывы:

Нет отзывов

Похожие инструкции для CH980

Бренд: Kohler Страницы: 108

Бренд: AL-KO Страницы: 182

Бренд: Nanni Страницы: 24

Бренд: RHINO Страницы: 9

Бренд: ILMOR Страницы: 78

Enduro RR 350 EFI 2016

Бренд: Beta Страницы: 158

SS2G SIDESHOT (DISCONTINUED) 8504075 REV 1 1198

Бренд: TJERNLUND Страницы: 14

Бренд: TJERNLUND Страницы: 27

Бренд: Wilesco Страницы: 4

Бренд: Yanmar Страницы: 308

Бренд: Honda Страницы: 64

Бренд: Honda Страницы: 86

Бренд: Wood-mizer Страницы: 13

Бренд: VACGEN Страницы: 13

Бренд: KTM Страницы: 159

Бренд: Marine Power Solutions Страницы: 23

Бренд: Jacobsen Страницы: 104

Бренд: YARDMAX Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды