Kohler CH980 Скачать руководство пользователя страница 79

Страница: 79 / 124

8.12

Section 8
Disassembly

NOTE

: These engines use valve stem seals on

the intake and exhaust valves. Use a
new seal whenever valves are removed,
or if the seal is deteriorated in any way.
Never reuse an old seal.

4. Repeat the above procedure for the other

cylinder head.

Do not

interchange parts from

one cylinder head to the other.

Remove Breather Assembly

1. Remove the four fasteners securing the breather

assembly, breather adapter (style based on spec),
and gaskets to the crankcase.

2. Carefully break the gasket seals and remove all

parts. Do not pry on the sealing surfaces as it
could cause damage resulting in leaks. Note the
assembly and orientation of parts. See Figures
8-48 and 8-49.

Remove Oil Reservoir and Pickup Screen

1. Remove the eight screws securing the oil

reservoir and gasket to engine.

Figure 8-48. Removing Breather Assembly.

Figure 8-50. Removing Oil Reservoir.

2. Remove the mounting screw and carefully work

the pickup screen off the end of the pickup tube.
See Figure 8-51.

Figure 8-51. Removing Pickup Screen.

Mounting Screw

Pickup Screen

Pickup Tube

Figure 8-49. Removing Breather Adapter.

Breather

Breather
Adapter

Breather Adapter
(Certain Models)

Gasket

Содержание CH980





























































































































Результаты поиска

Содержание CH980

Отзывы:

Похожие инструкции для CH980

Бренды по названию

Популярные бренды

Kohler CH980, Руководство по обслуживанию

Результаты поиска

Содержание CH980

Отзывы:

Похожие инструкции для CH980

Бренды по названию

Популярные бренды