Kohler CH980 Скачать руководство пользователя страница 72

Страница: 72 / 124

8.5

Section 8

Disassembly

Figure 8-15. Oil Sentry

™

Switch Location in

Closure Plate.

Remove Baffles and Intake Manifold

1. Remove the screws securing the valley baffles to

the cylinder heads and backing shroud assembly.

Figure 8-18. Removing Intake Manifold.

Remove Oil Sentry

™

(If Equipped)

1. Disconnect the lead from the Oil Sentry

™

switch.

2. Remove the Oil Sentry

™

switch from the closure

plate. See Figure 8-15.

Figure 8-16. Removing Valley Baffles.

Figure 8-17. Removing Outer Cylinder Baffles.

3. Remove the four hex flange screws securing the

intake manifold to the cylinder heads. Cut any
wire ties that secure the wiring harness or leads
to the intake manifold.

4. Remove the intake manifold and gaskets. See

Figure 8-18.

Pressure
Switch

2. Remove the four screws securing each of the

outer cylinder baffles in place. Two of the screws
are accessed from the backing shroud side. See
Figure 8-17.

Mounting
Screws

Mounting
Locations

Содержание CH980





























































































































Результаты поиска

Содержание CH980

Отзывы:

Похожие инструкции для CH980

Бренды по названию

Популярные бренды

Kohler CH980, Руководство по обслуживанию

Результаты поиска

Содержание CH980

Отзывы:

Похожие инструкции для CH980

Бренды по названию

Популярные бренды