Kohler CH980 Скачать руководство пользователя страница 123 | Manualshive

Страница: 123 / 124

background image

10.28

Section 10
Reassembly

Connect Spark Plug Leads

1. Connect the leads to the spark plugs. See Figure

10-114.

Figure 10-114. Connect Spark Plug Leads.

Prepare the Engine for Operation

The engine is now completely reassembled. Before
starting or operating the engine, be sure to do the
following.

1. Make sure all hardware is tightened securely.

2. Make sure the oil drain plugs, Oil Sentry

™

pressure switch, and a new oil filter are installed.

3. Fill the crankcase with the correct amount,

weight, and type of oil. Refer to oil
recommendations and procedures in Section 1
Safety and General Information, and in Section 6
Lubrication System.

4. Adjust the carburetor, idle fuel needles, or idle

speed adjusting screw as necessary. Refer to
Section 5, Fuel System and Governor.

Testing the Engine

It is recommended that the engine be operated on a
test stand or bench prior to installation in the piece of
equipment.

1. Set the engine up on a test stand. Install an oil

pressure gauge. Start the engine and check to be
certain that oil pressure (20 psi or more) is
present. Run the engine at idle for 2-3 minutes,
then 5-6 minutes more between idle and
midrange. Adjust the carburetor mixture
settings as necessary (as available).

2. Adjust the governed idle and high speed (RPM)

to required settings. Make sure the maximum
engine speed does not exceed 3900 RPM (no load).

«
...
121
122
123
124
»

Содержание CH980





























































































































Отзывы:

Нет отзывов

Похожие инструкции для CH980

Cobalt IP Analog

Бренд: DCCconcepts Страницы: 2

Бренд: Saito Страницы: 4

Бренд: Schartec Страницы: 16

Бренд: Vascat Страницы: 9

Бренд: Perkins Страницы: 108

Бренд: Bartec Varnost Страницы: 48

Бренд: Brother Страницы: 42

Бренд: Zenoah Страницы: 4

Бренд: Wood-mizer Страницы: 36

Бренд: Leadshine Technology Страницы: 55

Бренд: Yanmar Страницы: 32

Бренд: O.S. engine Страницы: 30

Бренд: DLE Страницы: 4

12K300 INTEK series

Бренд: Briggs & Stratton Страницы: 16

Бренд: Power smart Страницы: 28

Бренд: Toyota Страницы: 59

STEINER 75-70006A

Бренд: Schiller Страницы: 30

Бренд: SABB MOTOR Страницы: 142

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды