Kohler CH980 Скачать руководство пользователя страница 74

Страница: 74 / 124

8.7

Section 8

Disassembly

Figure 8-25. Removing Oil Filter Housing Adapter.

Remove Ignition Modules

1. Rotate the flywheel so the magnet is away from

the modules.

2. Remove the mounting screws and disconnect the

kill lead from the ignition modules. Note the
position of ignition modules. See Figure 8-26.

c. Remove the rubber valve and spring from the

cup. See Figure 8-24.

Figure 8-24. Rubber Valve and Spring Removed
from Cup.

2. Remove the screw securing the oil filter adapter

and individual O-Rings to the crankcase, then
carefully separate the parts. See Figure 8-25.

Figure 8-26. Removing Ignition Modules.

Remove Grass Screen and Cooling Fan

1. Remove the screws, attaching hardware and hex

studs securing the grass screen, stiffeners and
cooling fan to the flywheel. See Figures 8-27, 8-28
and 8-29.

Figure 8-27. Removing Grass Screen Fasteners.

Figure 8-28. Removing Mounting Studs.

Spring

Valve

Cup

Adapter
Mounting
Screw

Mounting
Screw

Adapter

Ignition
Modules

Содержание CH980





























































































































Результаты поиска

Содержание CH980

Отзывы:

Похожие инструкции для CH980

Бренды по названию

Популярные бренды

Kohler CH980, Руководство по обслуживанию

Результаты поиска

Содержание CH980

Отзывы:

Похожие инструкции для CH980

Бренды по названию

Популярные бренды