ILMOR MV10 650 Скачать руководство пользователя страница 1

Страница: 1 / 78

Ilmor High-Performance Marine, LLC

INTrOdUCTION

Please read this Owner’s Manual completely prior to operating the engine

and boat for the fi rst time. Th e Owner’s Manual contains information

critical for safe operation, and to activate and keep the limited warranty

statement in eff ect throughout the applicable warranty period. Continuing

the appropriate maintenance and care going forward can ensure long-term

enjoyment of your Ilmor High-Performance Marine engine. DO NOT

OPERATE THE ENGINE WITHOUT FIRST READING THE ENTIRE

OWNER’S MANUAL AND ALL SUPPORTING DOCUMENTATION, AS

WELL AS THE BOAT OWNER’S MANUAL.

WeLCOme

Welcome to the world of Ilmor High-Performance Marine. We would

like to thank you for selecting one of the fi nest and most durable High-

Performance Marine engine packages in the world for your boating needs.

Th ese engines represent a new opportunity for the boating world to enjoy

a reliable, high-performing power plant. Based on lightweight, high-output

designs, these engine packages are designed to deliver high-performance

boating pleasure without the typical complications. Along with their

high power and torque output, Ilmor High-Performance Marine engines

are notable for their smooth acceleration, ease of handling, reduced fuel

consumption, excellent drivability and user-friendly characteristics. Please

read this manual thoroughly so that you fully understand the proper care

and maintenance of your Ilmor High-Performance Marine product.

Содержание MV10 650















































































Результаты поиска

Содержание MV10 650

Отзывы:

Похожие инструкции для MV10 650

Бренды по названию

Популярные бренды

ILMOR MV10 650, Руководство пользователя

Результаты поиска

Содержание MV10 650

Отзывы:

Похожие инструкции для MV10 650

Бренды по названию

Популярные бренды