ILMOR MV10 650 Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 78

background image

SECTION 4

ILMOR HIGH-PERFORMANCE OWNER’S MANUAL

4-8

Ilmor High-Performance Marine, LLC

© 7/2013, Version 1.0

CHECK THE TRANSMISSION FLUID/OIL
LEVEL

Transmissions require lubrication to function properly. Your dealer can

verify the type of transmission in the boat. The amount of transmission

fluid/oil varies according to the product. See the requirements for

transmission fluid/oil in the transmission manufacturer’s manual.

NOTICE: Always use the recommended transmission fluid/oil. Damage
to the engine by use of low-quality or non-recommended transmission
fluid/oil will void the warranty. Overfill or underfill may also result in
serious damage to the engine and is not covered under warranty.

CHECK THE ENGINE OIL LEVEL

An accurate engine oil level reading will happen only after the engine has

run for at least 3 minutes at idle. This should be one of the last checks

performed prior to an outing. Run the engine with the boat in the body of

water.
1. After operating the engine at idle for at least 3 minutes, turn the engine

OFF and disconnect the engine safety starting switch. Open the engine

compartment. The engine oil dipstick is located on the side of the

engine.

2. Allow approximately 2 minutes before checking. Remove the dipstick

and wipe it off on a clean rag. Insert it fully and immediately remove.

Check that the oil level is between the FULL and LOW marks on the

dipstick. (Oil will expand as it is heated.)

3. Add oil if necessary through the oil fill neck and only enough to bring

oil between the two marks. Overfill may result in damage to the engine

that may not be covered by the warranty. Use oil as specified in Fluid

Specifications on page 11-1.

DO NOT USE OIL ADDITIVES AT

ANY TIME.

MV10

MV8-570

«
...
38
39
40
41
42
...
»

Содержание MV10 650















































































Отзывы:

Нет отзывов

Похожие инструкции для MV10 650

Бренд: Perkins Страницы: 112

PneuTorque PTS-52-500

Бренд: norbar Страницы: 30

Бренд: Polini Страницы: 34

Бренд: Parker Страницы: 32

COMBIFLUX FP 314 PVDF

Бренд: Flux Страницы: 28

Бренд: LCT Страницы: 25

Бренд: Slycma Страницы: 34

Enduro RR 350 EFI 2016

Бренд: Beta Страницы: 158

Бренд: BGS technic Страницы: 8

Бренд: Volvo Страницы: 88

Бренд: Robin America Страницы: 24

Бренд: Yanmar Страницы: 316

Бренд: Stiga Страницы: 168

Бренд: Beamz Страницы: 8

Бренд: Toyota Страницы: 78

POWER STROKE 2013

Бренд: Ford Страницы: 95

Бренд: nekos Страницы: 6

Бренд: DANA Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды