ILMOR MV10 650 Скачать руководство пользователя страница 72 | Manualshive

Страница: 72 / 78

background image

SECTION 9

ILMOR HIGH-PERFORMANCE OWNER’S MANUAL

9-8

Ilmor High-Performance Marine, LLC

© 7/2013, Version 1.0

Electronic Emission-Related Control Parts
Warranty

Systems Covered by

this Warranty

Parts Description

Fuel Metering

Fuel injectors
Fuel pump
Pressure regulator

Ignition

Spark plugs*
Ignition coil(s)
Ignition wire(s)

Miscellaneous Items

Camshaft Position sensor
Crankshaft Position sensor
Engine Coolant Temperature sensor
Intake Air Temperature sensor
Knock sensor
Manifold Absolute Pressure sensor
Throttle Position sensor
Electronic Control Unit
Electronic Throttle Control
Camshaft Position actuator solenoid valve**
Oil Pressure sensor**
Oxygen sensor**

* Covered up to, but not including, the first required replacement only.

See the Maintenance Schedule in the Owner’s Manual.

** As applicable

Direct Emission-Related Control Parts Warranty

Systems Covered by

this Warranty

Parts Description

Evaporative

Carbon canister
Fuel tank
Purge valve (if installed)
Low-permeation (non-metal) fuel hose(s)

«
...
70
71
72
73
74
...
»

Содержание MV10 650















































































Отзывы:

Нет отзывов

Похожие инструкции для MV10 650

Бренд: VAR-SPE Страницы: 80

Бренд: J.A.P Страницы: 21

Бренд: AL-KO Страницы: 182

Бренд: MSW Страницы: 159

Бренд: Scania Страницы: 55

Бренд: SICK Страницы: 20

Бренд: Lister Petter Страницы: 81

Бренд: Lister Petter Страницы: 100

Бренд: Baumr-AG Страницы: 25

Бренд: Lombardini Страницы: 12

Бренд: Lombardini Страницы: 44

Бренд: Lombardini Страницы: 54

Enduro RR 350 2015

Бренд: Beta Страницы: 158

Бренд: Yanmar Страницы: 2

Бренд: Yanmar Страницы: 2

Бренд: Yanmar Страницы: 48

Concept engines

Бренд: RB Страницы: 19

GX 610 standard

Бренд: Honda Страницы: 69

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды