manualshive.com logo in svg

ILMOR MV10 650, Руководство пользователя, Страница: 36 / 78

Поделиться
Скачать
ILMOR MV10 650 Скачать руководство пользователя страница 36

SECTION 4

 ILMOR HIGH-PERFORMANCE OWNER’S MANUAL

4-4

Ilmor High-Performance Marine, LLC 

© 7/2013, Version 1.0

CHECK THE POWER STEERING FLUID FOR 
ENGINES WITH INTEGRAL RESERVOIR

Because this process should be completed while the engine is cool (in order 

to avoid burns), it is recommended that this check be completed prior to 

starting the engine. If checked during an outing, allow the engine to cool. 

Be very careful to avoid burns from contact with hot engine parts. 
1.  Center the steering and stop the engine.
2.  Locate the power steering pump at the port side, front of the engine 

and remove the fill cap with integrated dipstick (level gauge).

3.  Proper fluid level is at the FULL mark.
4.  If necessary, add fluid to specified level. Use only fluid as outlined in 

Fluid Specifications on page 11-1.

1
2

3

1) FULL HOT Mark 

2) FULL COLD Mark

3) ADD Mark

NOTICE: If power steering fluid is not visible, contact your Ilmor High-
Performance Marine Service Center immediately. Severe engine 
damage could occur.

NOTE: Power steering fluid does not require changing. Review the 

Maintenance Schedule on page 7-1 for further details.

For remote power steering reservoir systems, see the boat manufacturer’s 

manual for proper maintenance instructions, or contact your authorized 

Ilmor service center for assistance.

Содержание MV10 650















































































Отзывы:

Нет отзывов