ILMOR MV10 650 Скачать руководство пользователя страница 27

Страница: 27 / 78

INTRODUCING ILMOR’S HIGH-PERFORMANCE ENGINES

Ilmor High-Performance Marine, LLC

2-9

VAPOR LOCK

Vapor lock is a condition that is primarily caused by high engine

compartment temperatures as a result of idling for long periods, idling

after periods of high speed running, or heat soak after shutdown due to the

discontinuance of water flow.

NOTICE: Always run your bilge blower for 4 minutes prior to starting the
engine and whenever you are operating at low speeds.

All Ilmor High-Performance Marine engines are equipped with our

exclusive Anti-Vapor Lock Valve, which separates fuel from vapor and

redirects the vapor back to the boat’s fuel tank, while directing high-

pressure liquid fuel to the engine.
In hotter climates and given the variations in gasoline formulations, the

possibility for vapor lock may still exist. Some steps to take to help alleviate

vapor lock are:
1. Always run your bilge blower for 4 minutes before starting the engine

and while running at lower speeds.

2. Partially open the engine hatch to allow for more air circulation prior

to starting.

WARNING!

Never run your boat underway with the

engine hatch open.

3. If vapor lock condition persists, contact your Ilmor High-Performance

Marine service center.

Содержание MV10 650















































































Результаты поиска

Содержание MV10 650

Отзывы:

Похожие инструкции для MV10 650

Бренды по названию

Популярные бренды

ILMOR MV10 650, Руководство пользователя

Результаты поиска

Содержание MV10 650

Отзывы:

Похожие инструкции для MV10 650

Бренды по названию

Популярные бренды