ILMOR MV10 650 Скачать руководство пользователя страница 71

Страница: 71 / 78

EMISSIONS

Ilmor High-Performance Marine, LLC

9-7

Emission Control System Warranty Parts

Ilmor High Performance Marine, LLC will warranty mechanical emission-

related components listed below 3 years or 150 hours of operation,

whichever first occurs, for engines with maximum power greater than 373

kW (500 bhp) but less than or equal to 485 kW (650 bhp); or for 1 year or

50 hours of operation, whichever first occurs, for engines with maximum

power greater than 485 kW (650 bhp); and select electronic and direct

emission-related control components for 3 years or 480 hours, whichever

first occurs.

Mechanical Emission-Related Components
Warranty

Systems Covered by

this Warranty

Parts Description

Fuel Metering

Intake valves

Air Induction

Intake manifold
Spark Arrestor/Air filter*

Lubrication

Oil pump (includes internal parts)

Positive Crankcase
Ventilation (PCV)

PCV valve
Oil filler cap

Exhaust System

Exhaust manifold (tailpipe not included)
Exhaust valves

Miscellaneous Items

Hoses
Clamps
Fittings
Tubing
Sealing gaskets or devices
Mounting hardware
Pulleys/Idlers
Serpentine Belt

* Covered up to, but not including, the first required replacement only.

See the Maintenance Schedule in the Owner’s Manual.

Содержание MV10 650















































































Результаты поиска

Содержание MV10 650

Отзывы:

ILMOR MV10 650, Руководство пользователя, Страница: 71 / 78

Результаты поиска

Содержание MV10 650

Отзывы: