ILMOR MV10 650 Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 78

background image

SECTION 6

ILMOR HIGH-PERFORMANCE OWNER’S MANUAL

6-4

Ilmor High-Performance Marine, LLC

© 7/2013, Version 1.0

SHIFTING GEARS

When shifting gears, always move the throttle/shift control lever smoothly

and quickly into gear. Hesitations and slow gear movement can damage the

shifting mechanism in the transmission. Always allow the engine speed to

fall to idle before making a gear shift.
The throttle/shift control lever must move forward 45 degrees of travel

from neutral to engage forward gear. Because the lever controls both

gearing and throttle response, continuing to move forward will increase

speed.
Reverse occurs when the throttle/shift control lever is pulled back from

neutral at least 45 degrees of travel.

NOTICE: Never move between forward-neutral-reverse when the engine
is above 800 rpm. Always allow the speed to decrease to 600–800 rpm
before completing the shift. Failure to do so may result in damage that is
not covered under warranty.

STOPPING THE BOAT

This is not a land vehicle. There are no brakes to be applied. To stop a boat

requires advance planning and operations that must be completed before

reaching the dock or bank.
1. Bring the throttle/shift control lever to neutral.
2. If the boat has been operated for an extended period of time, or at high

rpm, allow the engine a cool-down period at idle for several minutes.

3. Turn the key to the OFF position to stop the engine and drive train.
4. Coast into the dock or bank, following instructions provided by the

boat manufacturer’s Owner’s Manual to properly stop the boat without

damaging the hull.

«
...
44
45
46
47
48
...
»

Содержание MV10 650















































































Отзывы:

Нет отзывов

Похожие инструкции для MV10 650

Бренд: JetCat Страницы: 54

Бренд: O.S. engine Страницы: 5

MAX-15CV-R Series

Бренд: O.S. engine Страницы: 19

Xcelorin LOSB9400 3.5T

Бренд: Team Losi Страницы: 4

1550 STERNDRIVE

Бренд: Mercury Racing Страницы: 75

Бренд: DELTA DORE Страницы: 16

Бренд: dunkermotoren Страницы: 32

Бренд: Rotax Страницы: 13

MTR-DCI-...IO Series

Бренд: Festo Страницы: 182

Бренд: LAMBERT Страницы: 24

Бренд: Brother Страницы: 42

Бренд: Pacific Страницы: 48

Бренд: Volvo Penta Страницы: 29

Бренд: Volvo Penta Страницы: 56

Бренд: Volvo Penta Страницы: 96

Бренд: Clinton Страницы: 23

Бренд: Chamberlain Страницы: 20

Бренд: RIB Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды