ILMOR MV10 650 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 78

background image

Ilmor High-Performance Marine, LLC

© 7/2013, Version 1.0

2-1

Section 2

INTRODUCING ILMOR’S HIGH-
PERFORMANCE ENGINES

A

WARNING!

Always connect the positive (+) battery cable first.

After the positive cable is connected, then the negative (-) battery
cable can be attached. This minimizes the possibility of electrical
contact.

A

WARNING!

Always disconnect the negative battery cable (-)

first before disconnecting the positive battery cable (+). After the
negative battery cable is disconnected, the positive battery cable
can be disconnected. This minimizes the possibility of electrical
contact.

A

WARNING!

Replacement of any part of the fuel system must be

done with Ilmor-authorized parts only. If the fuel system supplying
the engine requires attention, any adjustment or replacement, the
procedure must be done by an authorized Ilmor High-Performance
Marine service center. The fuel lines are pressurized and can
only be disconnected with specialized tools. Failure to follow this
directive will void the warranty and can result in damage to the
boat and/or serious injury or death.

A

WARNING!

Never operate the engine without an adequate

amount of water flowing without interruption through the cooling
system. This requires the boat to be in an operational-sized body
of water or hooked up to the suction side of a raw water pump
by an Ilmor-approved water supply in a dealership. If the engine
operates without water in the cooling system, the exhaust system
will overheat and could potentially create an on-board fire. The
water pump impeller will also fail. Damage caused to the boat
under these circumstances will void the warranty and could result
in serious injury and/or death.

A

WARNING!

Never realign the wiring or in any way alter the

wiring of the engine. Doing so may result in damage to the engine,
which is not covered under warranty, and sufficient voltage may be
present to cause serious injury and/or death.

A

WARNING!

Never use jumper cables and a booster battery to

start your engine. Serious injury or death could result from fire or
explosion.

A

WARNING!

Never recharge your battery in the boat. Always

remove the battery for recharging in a well-ventilated area away
from fuel vapors, spark or flame. Failure to do so could result in
serious injury or death from fire or explosion.

«
...
17
18
19
20
21
...
»

Содержание MV10 650















































































Отзывы:

Нет отзывов

Похожие инструкции для MV10 650

Бренд: GGP Страницы: 56

Бренд: Grundfos Страницы: 36

Бренд: Tanaka Страницы: 7

Gasoline V6 90 Degree

Бренд: GMC Страницы: 94

Бренд: Agrimate Страницы: 32

ANORAD LZ Series

Бренд: Rockwell Automation Страницы: 64

Бренд: Toyota Страницы: 81

Бренд: Vetus Страницы: 134

Бренд: Orientalmotor Страницы: 4

Бренд: Saito Страницы: 7

Бренд: ACM Страницы: 22

rexroth MS2N03-A

Бренд: Bosch Страницы: 72

Бренд: Danfoss Страницы: 20

Бренд: Danfoss Страницы: 64

EM-PMI375-T1100

Бренд: Danfoss Страницы: 77

Бренд: Advanced Screenworks Страницы: 4

Бренд: DAYE Страницы: 80

Бренд: HPI Racing Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды