ILMOR MV10 650 Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 78

background image

SECTION 4

ILMOR HIGH-PERFORMANCE OWNER’S MANUAL

4-2

Ilmor High-Performance Marine, LLC

© 7/2013, Version 1.0

CHECK THE SEA STRAINER – PRE-ENGINE
START-UP

Because this process should be completed while the engine is cool (in

order to avoid burns), it is recommended that this check be completed

prior to starting the engine. If checking during an outing, allow the engine

to cool. Be very careful to avoid burns from contact with hot engine parts.
1. Ensure the engine is OFF and the engine safety starting switch is

disconnected. Leave the throttle/shift control lever in neutral.

2. Open the engine compartment and locate the seacock. Make sure this

is in the CLOSED position before proceeding.

3. Locate the sea strainer. Remove the cap/lid and check the screen for

debris. Remove any debris and rinse with water if necessary.

4. Reinstall the screen and screw on the cap/lid. Make sure the o-ring is in

place and do not overtighten.

5. Move the seacock into the OPEN position.

NOTICE: Make sure the seacock is back in the ON position. If this
operation is skipped, the engine will overheat, failing the raw water
pump impeller and causing severe engine problems. Make sure that
the cap/lid has been installed correctly and has not pinched the sealing
o-ring. This will cause air to be introduced into the system and could
cause the raw water impeller to fail, causing severe engine problems.

NOTICE: Always pay attention to any gauges or warning lights. Ignoring
elevated temperatures on a temperature gauge or any other evidence of
the engine operating at temperatures above recommended levels can
result in serious damage to the engine. Any resulting damage will not be
covered by the warranty.

NOTICE: This is a critical function of routine maintenance. Even clean-
appearing waterways may have debris such as pine needles or moss
that can enter the cooling system and create a blockage. Failure to
perform this function can result in serious overheating of the engine.
Damage to the engine and/or transmission caused by overheating is not
covered by warranty. Always pay attention to your temperature gauge,
even if you are carefully performing this check. Failure of the raw water
impeller or blockage of the transmission cooler are frequent causes of
overheating.

INCOMING

RAW WATER

OPEN

CLOSED

SEACOCK

STRAINER

TYPICAL SEACOCK AND STRAINER

«
...
32
33
34
35
36
...
»

Содержание MV10 650















































































Отзывы:

Нет отзывов

Похожие инструкции для MV10 650

Бренд: Exalto Страницы: 28

Бренд: Motorola Страницы: 82

Бренд: Allen-Bradley Страницы: 32

Бренд: ZF Страницы: 80

Бренд: Homa Страницы: 34

Бренд: Stober Страницы: 34

Бренд: LinMot Страницы: 40

Бренд: EMAK Страницы: 40

Бренд: Ford Страницы: 91

Бренд: Performance Страницы: 6

Бренд: Vetus Страницы: 84

Бренд: HandI Move Страницы: 26

Бренд: YASKAWA Страницы: 616

Бренд: KAMA Страницы: 25

Бренд: Saito Страницы: 22

Gast 4AM Series

Бренд: Idex Страницы: 8

Бренд: Omec Страницы: 10

Бренд: Bartec Varnost Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды