ILMOR MV10 650 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 78

background image

SECTION 2

ILMOR HIGH-PERFORMANCE OWNER’S MANUAL

2-2

Ilmor High-Performance Marine, LLC

© 7/2013, Version 1.0

A

WARNING!

Never run your boat underway with the engine hatch

open to avoid contact with moving parts or to avoid trapping air
under the hatch which may result in the hatch being blown off or
otherwise damaged or causing damage.

FUEL SYSTEM

Ilmor High-Performance Marine engines are equipped with multi-port

sequential fuel injection system, the most up-to-date system available in

the industry, featuring engine controllers that are capable of meeting all

emission and driveability requirements of marine applications with On-

Board Diagnostics Marine (OBD-M).

WARNING!

Replacement of any part of the fuel system must be done

with Ilmor-authorized parts only.

All fuel system lines and connections

must meet the requirements of U.S. Coast Guard (USCG) regulations. This

means that hoses must meet or exceed SAE Standard J1527 DEC85, and

hoses used for fuel delivery must meet or exceed specification in USCG

regulations, Sec. 183.540 for recreational boating. Additionally, all fuel

hose must meet the 15 g/m

2

limit for fuel permeation. All plumbing for

the fuel system on Ilmor engines, and the boats in which Ilmor authorizes

placement, meet or exceed all requirements. See Section 3, Fueling the

Engine, for additional information.

COOLING SYSTEM

Unlike automotive cooling systems that use radiators (air-to-fluid heat

exchangers) for cooling, marine engines use fluid-to-fluid heat exchangers.

Cooling is provided by the body of water in which the boat is operated. A

raw water pump (rubber impeller pump) draws water into the boat where

it is distributed to the engine, exhaust system, and heat exchangers in order

to maintain an acceptable range of engine operating temperatures.
Ilmor High-Performance Marine engines use a closed cooling system. In

this type of cooling system, engine coolant flows through the engine while

raw water flows through the exhaust headers.

WARNING!

Never operate the engine without an adequate amount of

water flowing without interruption through the cooling system.

Ensure

that the raw water pick-up remains clear of debris at all times. Even small

amounts can clog or block the pick-up, which is located beneath the

boat. The raw water pick-up MUST have an uninterrupted input of water

whenever the engine is running.

NOTICE: Marine growth occurs in brackish and salt water, and even in
what is referred to as “fresh” or salt-free water. Therefore, it is important
to flush the boat’s cooling system with fresh water after each use.

«
...
18
19
20
21
22
...
»

Содержание MV10 650















































































Отзывы:

Нет отзывов

Похожие инструкции для MV10 650

Бренд: Yamaha Страницы: 7

Command PRO EFI PCV850

Бренд: Kohler Страницы: 10

MAX-61SX-H RING WC Series

Бренд: O.S. engine Страницы: 36

Бренд: RADEMACHER Страницы: 60

Бренд: Pacific Страницы: 48

Бренд: Volvo Penta Страницы: 64

Бренд: Volvo Penta Страницы: 104

Бренд: Clarke Страницы: 18

Бренд: Volvo Penta Страницы: 132

Бренд: Clinton Страницы: 24

Бренд: Habasit Страницы: 54

Бренд: RAAMDECORATIE Страницы: 45

Бренд: Detroit Diesel Страницы: 224

Grove - Servo Max

Бренд: Seeed Страницы: 9

Бренд: DLE Страницы: 4

Бренд: DLE Страницы: 24

Бренд: New Holland Страницы: 41

Бренд: Honda Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды