ILMOR MV10 650 Скачать руководство пользователя страница 31 | Manualshive

Страница: 31 / 78

ILMOR MV10 650 Скачать руководство пользователя страница 31

FUELING THE ENGINE

Ilmor High-Performance Marine, LLC

© 7/2013, Version 1.0

3-3

Oxygenated Gasoline or Gasoline Containing
Alcohol

E-85 fuels are not to be used.

Use of this fuel may cause engine

performance to suffer and may damage vital fuel system components.

Leaded fuels may NOT be used in any Ilmor High-Performance Marine

engine.

Gasoline containing levels higher than 10% ethanol or gasoline containing

any methanol is

NOT TO BE USED

in Ilmor High-Performance Marine

engines. If the presence of alcohol in the gasoline is unknown, frequent

inspections of the fuel system are required.

When the Boat Is Not Used for A While

Ilmor recommends the use of STA-BIL fuel stabilizer if the boat consumes

less than a tank of fuel every 30 days. Today’s fuels are more susceptible to

degradation, and the use of a quality stabilizer helps ensure fewer problems

if the boat is used only on a limited basis.
If the boat has not been run for more than 30 days and fuel remains in the

tank—even stabilized fuel—the engine may run with reduced performance

until the existing fuel has been used. The manufacturer will not pay for

repairs to components that are damaged from poor-quality fuel as this is

not covered under the engine warranty.

NOTICE: Always perform the proper storage procedures when
storing the boat. Extended storage with fuel in the system can
affect fuel stability and may require system inspection and fuel filter
replacement when the boat returns to service. Fuel systems on all
boats equipped with Ilmor High-Performance Marine engines MUST
be properly prepared for storage periods exceeding 30 days. Owners
are encouraged to seek assistance from an authorized Ilmor High-
Performance Marine service center to properly prepare the drive train
for periods of inactivity exceeding one month. Damage due to improper
storage and/or winterization preparations is not covered under warranty.

Fuels Outside the United States and Canada

If the boat is operated outside the United States or Canada, it may be

more difficult to obtain lead-free fuel. As the engine components are

manufactured to function properly only with unleaded gasoline, it may be

necessary to search for refined unleaded gasoline.

E-85

«
...
29
30
31
32
33
...
»

Содержание MV10 650















































































Отзывы:

Нет отзывов