ILMOR MV10 650 Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 78

background image

BEFORE EACH USE

Ilmor High-Performance Marine, LLC

© 7/2013, Version 1.0

4-7

NOTE: Perform the next pre-checks after the engine has been run for several

minutes and then shut off.

CHECK THE SEA STRAINER – POST-ENGINE
START-UP

1.  Start the engine.
2.  Open the engine compartment and locate the sea strainer.
3.  After 20 seconds of run time, check the sea strainer to make sure it is

full of water with minimal air bubbles. If you have too much air in the

strainer, check to make sure the cap/lid is securely closed and sealed.

Check for leaks leading up to the oil/transmission cooler.

4. Close the engine compartment.

NOTICE: Air in the system could cause the raw water impeller to fail,
causing severe engine problems. If air in the system is persistent, visit
your local Ilmor service center.

CHECK THAT THE BATTERY IS FULLY
CHARGED

As the boat is started, check all gauges but pay particular attention to the

voltmeter.
With the key on, but before the engine is started, the voltmeter should

read above 12 volts. After starting the engine, check that the voltmeter

reads between 12.8 and 14.5 volts. An erratic reading can be a sign

of low voltage. The voltmeter is the best indication of the state of the

battery. However, it is not foolproof. While the reading will indicate

that the battery is producing current, if in a previous outing there

was reason to suspect a problem with the battery(ies), check with an

authorized Ilmor High-Performance Marine service center.
If the charge has fallen too low or if the battery is older or fails to hold a

charge at the expected level, the boat may not start. For additional questions

about your battery(ies), contact your boat manufacturer’s authorized dealer.

WARNING!

Always keep all sparks, flames and smoking materials away

from the battery charging area.

In the event of a dead battery, charge it

with a battery charger before attempting to start the engine. Jump-starting

from another boat or battery is dangerous. Charging a dead battery with the

alternator on the boat will put undue stress on the alternator, and that, in

turn, may cause it to fail.

«
...
37
38
39
40
41
...
»

Содержание MV10 650















































































Отзывы:

Нет отзывов

Похожие инструкции для MV10 650

Бренд: D+H Страницы: 20

Бренд: Man Страницы: 90

Бренд: Kohler Страницы: 4

Бренд: Daewoo Страницы: 199

Vickers M2-200 Series

Бренд: Eaton Страницы: 16

RADIOMODULE 2G4

Бренд: Grundfos Страницы: 76

Quantum Jazzy 1400

Бренд: Pride Mobility Страницы: 2

Бренд: Price Industries Limited Страницы: 17

Бренд: AL-KO Страницы: 132

Бренд: Volvo Penta Страницы: 130

Бренд: YS Страницы: 2

Бренд: Volvo Страницы: 88

BEVELMASTER 204B

Бренд: TRI tool Страницы: 46

Бренд: DANA Страницы: 3

Бренд: DANA Страницы: 3

Бренд: KRESS Страницы: 46

Бренд: Turn Key Страницы: 16

Бренд: Yanmar Страницы: 317

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды