Kirby Morgan SuperLite 27 Скачать руководство пользователя страница 50

Страница: 50 / 168

SuperLite

There is a risk with this method that the emergency

gas could be lost if the hose or the first stage itself

develops a leak. Probably the most serious problem

with any of the other possible configurations is that

the first stage will almost certainly flood if it is not

pressurized while you are underwater.
If the regulator floods and is not promptly serviced,

it will not perform properly when you need it in an

emergency. As a diver, you always must decide how

much risk and what types of risk you are willing to

expose yourself to when you dive. It’s up to each

individual to make an informed choice regarding

how to configure your bail-out system.

Always be sure to check the pressure in your bail-out

bottle before you dive.

KMDSI strongly recommends the use of a submers

ible pressure gauge with every bail-out system. Not

only does this make it very easy to check your emer

gency gas pressure prior to diving, it also allows you,

in most cases, to periodically check the pressure in

your system while you dive. In this way, if you have

a leak, you will probably figure it out and will be able

to take appropriate action.

Some divers, keep the EGS gas cylinder

valve shut during the dive. Their rationale

being; in the event of an emergency, they

will simply open the EGS cylinder valve

thus eliminating any EGS air/gas unknow-

ingly being lost due to either a 1st stage

failure or EGS hose failure.

KMDSI strongly recommends never diving

with the EGS tank (cylinder) valve shut.

The reasoning behind this is twofold.

First, with the EGS cylinder valve open,

gas is immediately available in the event

of topside gas interruption via the EGS

valve on the side block simply by open-

ing it. Secondly, and most importantly, if

the EGS regulator (1st stage) is not pres-

surized, during descent it is possible that

sea water will leak through the first stage

intermediate circuit and regulator, causing

failure of the EGS regulator and resulting

in possible injury or death.

WARNING

Содержание SuperLite 27








































































































































































Результаты поиска

Содержание SuperLite 27

Отзывы:

Бренды по названию

Популярные бренды

Kirby Morgan SuperLite 27, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание SuperLite 27

Отзывы:

Бренды по названию

Популярные бренды