Kirby Morgan SuperLite 27 Скачать руководство пользователя страница 34

Страница: 34 / 168

SuperLite

The KMDSI Overpressure Relief Valve, (part number

200-017) is fully adjustable and rebuildable and has

been designed to relieve any over-pressurization of

the first stage regulator greater than the desired set-

ting.
Every bailout (Emergency Gas System or EGS) first

stage regulator must be fitted with an overpressure

relief valve to prevent over pressurization of the EGS

L.P hose and possible total loss of the emergency

supply gas in event of regulator failure.

The over-pressure relief valve

should be installed on every first

stage used for bailout.

KMDSI Part #200-017

NOTE: This valve can be adjusted for vari-

ous relief pressures.

WARNING

Be sure the Emergency air/gas first stage

regulator is fitted with a relief valve to

help prevent over-pressurization of the

emergency gas supply hose. A leaky first

stage can overpressure the hose result-

ing in hose rupture. This would cause a

loss of the entire emergency gas supply,

with possible serious injury or death.

2.8.4 Helmet Attachment to the Diver

On the helmet, the neck ring on the base of the helmet

shell has a machined O-ring sealing surface. The O-

ring that seals against this surface sits inside the neck

dam ring assembly. The neck dam ring is actually a

three part ring, consisting of the upper split rings and

the lower stepped ring. The neck dam is captured

(sandwiched) between these parts.
The locking collar and neck pad assembly has a

smaller opening than a diver’s head so the helmet

cannot be accidentally dislodged on most divers. The

neck pad pushes against the neck dam and lower por-

tion of the head cushion firmly securing the helmet

to the diver’s head. The neck pad also helps prevent

neck dam ballooning. Each diver must personally

adjust the fit on his helmet by adjusting the neck

pad, as well as the head cushion. All of these parts

together help provide a good fit.

Both sides of the helmet locking collar have a latch

catch block to receive the locking sealed pull pins. If

the sealed pull pins are turned to the locking position

while the locking collar is open, the locking collar

will snap into the locked position when it is pushed

up into the helmet neck ring. The sealed pull pin

on each side must be pulled to release the locking

collar to remove the helmet. This system provides

an extremely secure method of attaching the helmet

to the diver.
The head cushion is made from layers of open cell

foam inserted in a head shaped nylon bag. Adding

or subtracting foam layers from the bag can adjust

the fit of the head cushion. The head cushion must

be adjusted correctly for the helmet to fit properly.
The chin strap inside the helmet must be fastened

properly under the diver’s chin prior to diving. This

is essential for the diver’s comfort. Also, in the rare

case where the pull pins are opened underwater, and

the helmet separates from the neck dam, the neck

strap will help to keep the helmet on the diver’s head.
The relationship between the locking collar assembly,

head cushion, chin cushion, and helmet shell all affect

the fit of the helmet.

Hinge

bolt

Nut

Locking

collar

Neck pad

Adjustment nut

Washer

Screw

T-washer

O-ring

Split

Ring

Neck

dam

Stepped

Ring

Pull

Strap

The Neck Dam and Locking Collar Assemblies.

Содержание SuperLite 27








































































































































































Результаты поиска

Содержание SuperLite 27

Отзывы:

Бренды по названию

Популярные бренды

Kirby Morgan SuperLite 27, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание SuperLite 27

Отзывы:

Бренды по названию

Популярные бренды