Kirby Morgan SuperLite 27 Скачать руководство пользователя страница 107

Страница: 107 / 168

SuperLite

adjustment knob is turned in, the leak may continue.
1) One method to check for this is for the diver to

place the demand regulator above the neck dam by

looking up. Free flow from a leaky neck dam should

cease as long as the helmet is in the upright position.
2) Ensure the demand regulator bias adjustment knob

(98) is properly adjusted for the supply pressure.
3) During ascent the regulator will free flow if the

supply pressure to the helmet is not backed off (top

side) or, the diver does not adjust “in” (clockwise),

the demand regulator adjustment knob as the diver’s

depth and the ambient pressure decreases.
4) If the preceding steps were checked and the demand

regulator still steady flows the regulator requires

adjustment.

7.9 Oral Nasal

7.9.1 Oral Nasal Removal

Tools Required:

7/16 inch Open-end Wrench
The oral nasal mask is easily replaced.
1) Remove the nose block device first. See Chapter 8

for this procedure.
2) Remove the microphone.
3) The oral nasal mask can then be pulled off the

regulator mount nut. It is held on by a snap fit.

7.9.2 Inspection of Oral Nasal

1) Inspect the oral nasal mask. If it is torn, damaged

or aged it must be replaced.
2) Inspect the oral nasal valve. If it is torn or damaged

it must be replaced.
3) Remove the valve body by pushing it out of the

oral nasal.

7.8.11 Regulator Has Low or No Flow When

Pressurized

Tools Required:

Regulator Adjustment Tools, (Part #525-620)

1/4 inch Flat Blade Attachment on Torque Screwdriver
NOTE: If there is low or no flow when the regulator

is pressurized, and the lever is very loose (travels

more than 1/8 inch at the roller end), the nut must be

tightened.
1) Adjust demand regulator bias adjustment knob “in”,

i.e., clockwise.
2) Ensure supply pressure is adjusted between 135-150

p.s.i.g. (9.3-10.3 bar).
3) Back the demand regulator bias adjustment knob

(98) out counterclockwise until a slight steady flow

develops. Then adjust the knob in clockwise until the

free-flow just stops. Depress the lever several times

to ensure the regulator is stabilized.
4) Recheck the lever play at the purge button ensuring

1/16 inch (1.5 mm) to l/8 inch (3.0 mm) of free travel

before the purge button comes in contact with the

diaphragm actuating a slight flow of gas. If a slight

flow of gas develops with the purge button depressed

less than 1/16 inch (1.5 mm), the lever will require

slightly more play. If the purge button travels greater

than 1/8 inch (3.0 mm), the lever will require a reduc

tion of play by adjusting.
5) Recheck that gas source pressure is set between

135-150 p.s.i.g. The gas source must be capable of

supplying 4.5 a.c.f.m. (127.4 L/min per diver) at the

required over bottom pressures for the depth of the

dive per Section 2, Tables 1 and 2.
6) If the preceding steps were satisfactory, check the

following helmet/mask parts for foreign debris in the

air/gas passages:

a. One-way valve

b. Side block assembly

1. Defogger valve

2. Emergency Valve Assembly

3. Bent Tube Assembly

7.8.12 Unexplained Demand Regulator Free

Flow

Any leak in the neck dam when the diver is face down

will cause gas to vent out into the water from the inside

of the helmet. This causes the demand regulator to

steady flow, making up for the vented gas. Even if the

Содержание SuperLite 27








































































































































































Результаты поиска

Содержание SuperLite 27

Отзывы:

Бренды по названию

Популярные бренды

Kirby Morgan SuperLite 27, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание SuperLite 27

Отзывы:

Бренды по названию

Популярные бренды