Kirby Morgan SuperLite 27 Скачать руководство пользователя страница 47

Страница: 47 / 168

SuperLite

without the main gas supply, and the gas consump

tion rate. Regardless of the cylinder used, it should

be of sufficient volume to allow the diver to ascend

at a normal rate or transit to a point where a normal

gas supply can be reestablished.

European C.E. ONLY

In European countries that have adopted C.E. certi

fication,

only C.E. certified cylinders are allowed to

be used and must have a minimum charged capacity

available to the diver of 1400 N/l (50 scf). The emer

gency gas supply must only be fitted with a KMDSI

first stage regulator and have a KMDSI over pressure

relief valve installed (Part # 200-017).

The relief must

be adjusted to start lifting at approximately 20 p.s.i.g.

(1.4 bar) above the regulator intermediate setting.

The purpose of the relief valve is to allow pressure to

vent off in the event the first stage regulator develops

a leak or creeps. Without a pressure relief valve, the

hose could rupture and the emergency gas supply

would be lost.

The emergency air/gas tank must be fitted with a good

quality first stage regulator to reduce the pressure to

Most commercial divers wear a harness (separate

from the weight belt) that is used for several purposes.

The harness is fitted with large metal rings (usually

brass or stainless steel). The umbilical is hooked into

one of these rings to keep any strain off the helmet.

In addition, the rings on the harness are used to hang

tools and other equipment. Usually the harness is also

designed to provide a means of lifting an unconscious

diver from the water. This harness is the best method

of securing the emergency breathing gas to the diver.
A small tank can be mounted horizontally on the

lower rear or front, while larger tanks are usually

mounted vertically in the center back similar to a

SCUBA diver’s tank. Some harness designs incor

porate a cloth enclosure into which the tank fits.

The entire tank, valve, and regulator are enclosed in

fabric. This helps to prevent snagging.
When determining the size of the emergency gas

cylinder to use, several factors must be considered.

The divers depth, the length of time the diver may be

less than 225 p.s.i.g. (16 bar) ambient diver pressure.

The helmet cannot properly handle more pressure

without modification. The KMDSI SuperFlow

First

Stage SCUBA

regulator (Part #305-161) is an excel

lent device for this use. These regulators reduce the

tank pressure to approximately 145 p.s.i.g. (9.9 bar).

Other quality high performance SCUBA regulators

may also be used. Connect the first stage hose with

a set of quick disconnecting locking sleeves to the

emergency valve assembly located on the side block.

The first stage regulator must have at least two low

pressure ports. One port is used for the connector

hose to the emergency valve and the second is used to

Do not dive without a diver worn Emer-

gency Gas System (EGS). If the main gas

supply is lost, you will have nothing to

breathe and may drown.

WARNING

The diving harness must have a provision for attach

ing the emergency gas supply and a place to attach

the diver’s umbilical.

Use a good quality first stage for

your emergency gas supply.

Содержание SuperLite 27








































































































































































Результаты поиска

Содержание SuperLite 27

Отзывы:

Бренды по названию

Популярные бренды

Kirby Morgan SuperLite 27, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание SuperLite 27

Отзывы:

Бренды по названию

Популярные бренды