Keysight Technologies Infiniium MSOV 084A Скачать руководство пользователя страница 81

Страница: 81 / 164

Troubleshooting

Infiniium V-Series Oscilloscopes Service Guide

MSO Assembly Troubleshooting

This section describes problems that may occur when an MSO assembly is

installed, and how to troubleshoot them. The MSO printed circuit assembly is

located below the lower acquisition board, with the components facing downward.

LEDs on MSO assemblies

The MSO printed circuit board has two sets of LEDs. One set is visible from the

right side of the oscilloscope, and the other set is visible from the left side.

MSO LEDs on the right side of the oscilloscope

To see the LEDs on the right

side, look straight in through the vent holes and see the lights pointed toward the

bottom of the oscilloscope. These two red LEDs turn on when the oscilloscope is

turned on, indicating that the comparators are off. The LEDs stay on until the

FPGA is programmed by the scope application software; then the software turns

the LEDs off when it turns the comparators on.
If the LEDs turn on after the application is running, a thermal problem likely was

detected. A warning appears. To resolve the problem, shut down the scope and

allow it to cool. Make sure the fan holes are not blocked, and allow at least 4

inches of space next to the oscilloscope. Restart the scope and verify that all fans

are working.

MSO LEDs on the left side of the oscilloscope

The LEDs on the left side can

be seen only as a reflection in the lower sheet metal as you look through the fans.

These LEDs are off until the FPGA is programmed successfully, which occurs

shortly after the scope application starts.
One of the LEDs turns on and remains on after the FPGA is programmed. The other

LED will start blinking steadily at about 1.6 Hz if the 250 MHz clock coming from

the backplane board is working properly. If the LED is not blinking steadily, verify

that the backplane board was modified correctly to be used with the MSO board.

That is, in the clock area on the top side of the backplane board, R352 and R353

should be loaded with 0 ohm resistors. The same area on the bottom side of the

board should not have resistors on R330 and R332. If this clock rework has not

been done, you will see an error message indicating an option card DAC failure

when the application starts up.

Содержание Infiniium MSOV 084A





































































































































































Результаты поиска

Содержание Infiniium MSOV 084A

Отзывы:

Похожие инструкции для Infiniium MSOV 084A

Бренды по названию

Популярные бренды

Keysight Technologies Infiniium MSOV 084A, Руководство по обслуживанию

Результаты поиска

Содержание Infiniium MSOV 084A

Отзывы:

Похожие инструкции для Infiniium MSOV 084A

Бренды по названию

Популярные бренды