Keysight Technologies Infiniium MSOV 084A Скачать руководство пользователя страница 11

Страница: 11 / 164

General Information

Infiniium V-Series Oscilloscopes Service Guide

Measurement Category

The Infiniium V-Series oscilloscopes are not intended to be used for measurements

in Measurement Category II, III, or IV.

Measurement Category Definitions

The "Not rated for CAT II, III, IV" measurement category is for measurements

performed on circuits not directly connected to MAINS. Examples are

measurements on circuits not derived from MAINS, and specially protected

(internal) MAINS derived circuits. In the latter case, transient stresses are variable;

for that reason, the transient withstand capability of the equipment is made known

to the user.
Measurement category II is for measurements performed on circuits directly

connected to the low voltage installation. Examples are measurements on

household appliances, portable tools and similar equipment.
Measurement category III is for measurements performed in the building

installation. Examples are measurements on distribution boards, circuit-breakers,

wiring, including cables, bus-bars, junction boxes, switches, socket-outlets in the

fixed installation, and equipment for industrial use and some other equipment, for

example, stationary motors with permanent connection to the fixed installation.
Measurement category IV is for measurements performed at the source of the

low-voltage installation. Examples are electricity meters and measurements on

primary overcurrent protection devices and ripple control units.

WARNING

The product is for use only on circuits that are NOT directly connected to mains. It is

NOT intended for measurements on CAT II, CAT III, or CAT IV circuits.

Содержание Infiniium MSOV 084A





































































































































































Результаты поиска

Содержание Infiniium MSOV 084A

Отзывы:

Похожие инструкции для Infiniium MSOV 084A

Бренды по названию

Популярные бренды

Keysight Technologies Infiniium MSOV 084A, Руководство по обслуживанию

Результаты поиска

Содержание Infiniium MSOV 084A

Отзывы:

Похожие инструкции для Infiniium MSOV 084A

Бренды по названию

Популярные бренды