Keysight Technologies Infiniium MSOV 084A Скачать руководство пользователя страница 67

Страница: 67 / 164

Troubleshooting

Infiniium V-Series Oscilloscopes Service Guide

It is also possible that there is a short circuit on the bulk +12 V supply trace

somewhere in the system, which would also cause the unit not to power on. If so,

you need to isolate the assembly that is shorted. You do not need to remove the

acquisition or backplane assemblies to perform the following steps.

With the power turned off, disconnect the bulk +12 V supply, but do not remove

the supply from the oscilloscope.

On the backplane assembly, measure the resistance across the FET (Q1409,

located in the upper right corner of the backplane) b12 V and ground

as shown below, or measure the resistance across the bulk supply input pins on

the backplane assembly. Make sure the red lead is plugged into the HI output

and the black lead is plugged into the LO or COMMON input of the DVM. On a

good backplane assembly, you should measure about 700 ohms. If there is a

short on this board, you would measure something very near 0 ohms.

Power supply disconnect

Measuring the backplane assembly resistance b12 V and ground across Q1409

Содержание Infiniium MSOV 084A





































































































































































Результаты поиска

Содержание Infiniium MSOV 084A

Отзывы:

Похожие инструкции для Infiniium MSOV 084A

Бренды по названию

Популярные бренды

Keysight Technologies Infiniium MSOV 084A, Руководство по обслуживанию

Результаты поиска

Содержание Infiniium MSOV 084A

Отзывы:

Похожие инструкции для Infiniium MSOV 084A

Бренды по названию

Популярные бренды