Keysight Technologies Infiniium MSOV 084A Скачать руководство пользователя страница 73

Страница: 73 / 164

Troubleshooting

Infiniium V-Series Oscilloscopes Service Guide

Motherboard Verification

If you have been through the Power Supply Troubleshooting section of this chapter

and the oscilloscope still does not stay powered up, the problem may be with the

motherboard. To diagnose this problem, follow these steps.

Remove the top panel.

Turn the oscilloscope on.

If the unit beeps once after about 5 to 10 seconds but fails to boot up, the

motherboard is defective and needs to be replaced.

If the unit fails to beep after it is powered on, then measure the potential

relative to the chassis at pin 9 of J1201 on the backplane board (see figure

below). Pin 9 is the reset line for the motherboard and is controlled by the

backplane. You should measure about 3.3 V. If the potential you measure is

correct, but the unit still has not beeped and started up, the motherboard is

defective and needs to be replaced.

If the potential you measure is not correct, shut the oscilloscope down and

unplug the AC cord from the rear of the instrument.

Unplug the front panel power cable, the two large power cables that go to the

motherboard (J1201 and J1202), and the red and blue SATA cables (J900 and

J901) from the PCIe-to-SATA adapter board on the backplane assembly. Do not

allow the two SATA cables to touch the backplane assembly and cause a short

circuit.

Plug the AC power back into the oscilloscope and turn the unit on if it does not

come on automatically.

Measure the potential relative to the chassis at pin 9 of J1201 again.

If you measure the required 3.3 V, the motherboard is defective and needs to be

replaced.

If you did not measure the correct voltage, the backplane assembly is defective

and must be replaced.

Measure potential relative to chassis at pin 9 of J1201

Содержание Infiniium MSOV 084A





































































































































































Результаты поиска

Содержание Infiniium MSOV 084A

Отзывы:

Похожие инструкции для Infiniium MSOV 084A

Бренды по названию

Популярные бренды

Keysight Technologies Infiniium MSOV 084A, Руководство по обслуживанию

Результаты поиска

Содержание Infiniium MSOV 084A

Отзывы:

Похожие инструкции для Infiniium MSOV 084A

Бренды по названию

Популярные бренды