Keysight Technologies Infiniium MSOV 084A Скачать руководство пользователя страница 71

Страница: 71 / 164

Troubleshooting

Infiniium V-Series Oscilloscopes Service Guide

Apply AC power and turn the oscilloscope on if it does not start up on its own.

Notice whether the trigger ICs fan is turning. If it is not, replace it and redo this

part of the diagnostic test. If it is turning and the oscilloscope still turns off again,

then consider these possibilities:
• If the trigger ICs fan was turning, the problem is most likely that the rotation

sensor on the ICs fan is defective. Replace the trigger ICs fan and redo this part

of the diagnostic test.

• If the oscilloscope stays on after you reset the shutdown logic (by removing AC

power for 30 seconds) and powered it back on, then you have fixed the

shutdown problem.

• If the oscilloscope shuts down again after you have replaced the trigger ICs fan,

then the problem could be that the rotation sensor for all the fans located on

the backplane assembly failed, so replace the backplane assembly and redo

this part of the diagnostic test.

Trigger ICs fan on backplane assembly

Содержание Infiniium MSOV 084A





































































































































































Результаты поиска

Содержание Infiniium MSOV 084A

Отзывы:

Похожие инструкции для Infiniium MSOV 084A

Бренды по названию

Популярные бренды

Keysight Technologies Infiniium MSOV 084A, Руководство по обслуживанию

Результаты поиска

Содержание Infiniium MSOV 084A

Отзывы:

Похожие инструкции для Infiniium MSOV 084A

Бренды по названию

Популярные бренды